Samsung Microwave Error Codes

Select form the list of Samsung Microwave error codes below for the code meaning and possible issues that may be causing the fault to display.

C-20
C-21
C-A1
C-d0
C-F0
C-F2
E-01
E-02
E-03
E-04
E-05
E-06
E-08
E-09
E-11
E-12
E-13
E-14
E-21
E-22
E-23
E-24
E-25
E-26
E-31
E-32
E-33
E-34
E-35
E-36
E-41
E-42
E-43
E-44
E-45
E-46
E-47
E-51
E-53
E-54
E-61
E-62
E-63
E-83
E-A1
SE
TE
Samsung Microwave Error Codes

Why is my Samsung Microwave displaying error codes?

Your Samsung Microwave will display error codes when the main control panel internal diagnostics system has detected a problem.

How can I reset Samsung Microwave Error Codes

The first thing to try is switching the Microwave main power supply off for 60 seconds. This usual only works if the fault was set due to a supply voltage fluctuation from a storm or power outage. It may also work if the problem is intermittent. Unfortunately this might only be a short term solution because if the problem is intermittent and the fault returns, the error code will display again.

If that doesn’t work, the problem triggering the error code will need to be repaired in order to clear the fault code.

Why is my Samsung Microwave not working?

Some Samsung Microwave error codes will disable the appliance from operating. The error code will need to be resolved in order for the appliance to function normally again.

What does C-20 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an C-20 fault code, it is indicating a Over Temperature Error has been detected by the internal self diagnostics system.

An C-20 Over Temperature Error will set if the control board detects The oven temperature is higher than 500F ̊F(265 ̊c) while oven is on.

The most common issues that will cause an C-20 Over Temperature Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The temperature sensor is defective.
  • Wiring issue between the main PCB and the temperature sensor.

Try turning the Microwave main power supply off for 1 minute. If the C-20 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does C-21 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an C-21 fault code, it is indicating a Abnormal Temperature Error has been detected by the internal self diagnostics system.

An C-21 Abnormal Temperature Error will set if the control board detects An abnormal temperature is detected while the oven is on.

The most common issues that will cause an C-21 Abnormal Temperature Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The temperature sensor is defective.
  • Wiring issue between the main PCB and the temperature sensor.

Try turning the Microwave main power supply off for 1 minute. If the C-21 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does C-A1 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an C-A1 fault code, it is indicating a Damper Error has been detected by the internal self diagnostics system.

An C-A1 Damper Error will set if the control board detects The damper has not reached the desired position within 40 seconds.

The most common issues that will cause an C-A1 Damper Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The damper motor is defective.
  • The damper switch is defective.
  • Wiring issue between the main PCB and the damper motor or switch.

Try turning the Microwave main power supply off for 1 minute. If the C-A1 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does C-d0 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an C-d0 fault code, it is indicating a Shorted Key Error has been detected by the internal self diagnostics system.

An C-d0 Shorted Key Error will set if the control board detects Any button is stuck or held for more than 10 seconds.

The most common issues that will cause an C-d0 Shorted Key Error to display on a Samsung Microwave are:

  • The keypad is defective.
  • The microwave control PCB is defective.
  • Wiring issue between the keypad and the control PCB.

Try turning the Microwave main power supply off for 1 minute. If the C-d0 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does C-F0 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an C-F0 fault code, it is indicating a Communication Error has been detected by the internal self diagnostics system.

An C-F0 Communication Error will set if the control board detects There is a communication error between the main PCB and the touch PCB.

The most common issues that will cause an C-F0 Communication Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The touch PCB is defective.
  • Wiring issue between the main PCB and the sub PCB.

Try turning the Microwave main power supply off for 1 minute. If the C-F0 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does C-F2 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an C-F2 fault code, it is indicating a Touch Key Error has been detected by the internal self diagnostics system.

An C-F2 Touch Key Error will set if the control board detects Any button is stuck or held for more than 10 seconds.

The most common issues that will cause an C-F2 Touch Key Error to display on a Samsung Microwave are:

  • The keypad is defective.
  • The microwave control PCB is defective.
  • Wiring issue between the keypad and the control PCB.

Try turning the Microwave main power supply off for 1 minute. If the C-F2 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-01 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-01 fault code, it is indicating a Door Open Error has been detected by the internal self diagnostics system.

An E-01 Door Open Error will set if the control board detects The door is open during operation.

The most common issues that will cause an E-01 Door Open Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The door switch is defective.
  • The door latch is defective.
  • Wiring issue between the main PCB and the door switch.

Try turning the Microwave main power supply off for 1 minute. If the E-01 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-02 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-02 fault code, it is indicating a Oven cook Temp Error has been detected by the internal self diagnostics system.

An E-02 Oven cook Temp Error will set if the control board detects The oven cooking temperature cannot reach the desired setting within the set amount of time.

The most common issues that will cause an E-02 Oven cook Temp Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The temperature sensor is defective.
  • The heater is defective.
  • Wiring issue between the main PCB and the temperature sensor or heater circuit.

Try turning the Microwave main power supply off for 1 minute. If the E-02 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-03 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-03 fault code, it is indicating a Grill Cook Temp Error has been detected by the internal self diagnostics system.

An E-03 Grill Cook Temp Error will set if the control board detects The grill cooking temperature cannot reach the desired setting within the set amount of time.

The most common issues that will cause an E-03 Grill Cook Temp Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The temperature sensor is defective.
  • The heater is defective.
  • Wiring issue between the main PCB and the temperature sensor or heater circuit.

Try turning the Microwave main power supply off for 1 minute. If the E-03 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-04 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-04 fault code, it is indicating a Convection Cook Temp Error has been detected by the internal self diagnostics system.

An E-04 Convection Cook Temp Error will set if the control board detects The convection cooking temperature cannot reach the desired setting within the set amount of time.

The most common issues that will cause an E-04 Convection Cook Temp Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The temperature sensor is defective.
  • The convection heater is defective.
  • The convection fan is defective.
  • Wiring issue between the main PCB and the temperature sensor, fan or heater circuit.

Try turning the Microwave main power supply off for 1 minute. If the E-04 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-05 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-05 fault code, it is indicating a Combination Cook Temp Error has been detected by the internal self diagnostics system.

An E-05 Combination Cook Temp Error will set if the control board detects The combination cooking temperature cannot reach the desired setting within the set amount of time.

The most common issues that will cause an E-05 Combination Cook Temp Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The temperature sensor is defective.
  • The heater is defective.
  • The power inverter or magnetron is defective.
  • Wiring issue between the main PCB and the temperature sensor, heater or magnetron circuit.

Try turning the Microwave main power supply off for 1 minute. If the E-05 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-06 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-06 fault code, it is indicating a Sensing Error has been detected by the internal self diagnostics system.

An E-06 Sensing Error will set if the control board detects The sensor fails to sense that the swing heater has stopped for 20 seconds during cooking.

The most common issues that will cause an E-06 Sensing Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The sensor is defective.
  • Wiring issue between the main PCB and the sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-06 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-08 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-08 fault code, it is indicating a Oven Error has been detected by the internal self diagnostics system.

An E-08 Oven Error will set if the control board detects Spit air getting into the oven cavity.

The most common issues that will cause an E-08 Oven Error to display on a Samsung Microwave are:

  • No information is available for this error code.

Try turning the Microwave main power supply off for 1 minute. If the E-08 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-09 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-09 fault code, it is indicating a Damper Error has been detected by the internal self diagnostics system.

An E-09 Damper Error will set if the control board detects The damper has not reached the desired position within 2 minuits.

The most common issues that will cause an E-09 Damper Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The damper motor is defective.
  • The damper switch is defective.
  • Wiring issue between the main PCB and the damper motor or switch.

Try turning the Microwave main power supply off for 1 minute. If the E-09 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-11 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-11 fault code, it is indicating a Gas Sensor Error has been detected by the internal self diagnostics system.

An E-11 Gas Sensor Error will set if the control board detects The gas sensor is open.

The most common issues that will cause an E-11 Gas Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The gas sensor is defective.
  • Wiring issue between the main PCB and the gas sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-11 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-12 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-12 fault code, it is indicating a Gas Sensor Error has been detected by the internal self diagnostics system.

An E-12 Gas Sensor Error will set if the control board detects The gas sensor is shorted.

The most common issues that will cause an E-12 Gas Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The gas sensor is defective.
  • Wiring issue between the main PCB and the gas sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-12 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-13 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-13 fault code, it is indicating a Gas Sensor Error has been detected by the internal self diagnostics system.

An E-13 Gas Sensor Error will set if the control board detects The gas sensor reading is abnormal.

The most common issues that will cause an E-13 Gas Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The gas sensor is defective.
  • Wiring issue between the main PCB and the gas sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-13 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-14 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-14 fault code, it is indicating a Gas Sensor Error has been detected by the internal self diagnostics system.

An E-14 Gas Sensor Error will set if the control board detects Dry up or no load error.

The most common issues that will cause an E-14 Gas Sensor Error to display on a Samsung Microwave are:

  • Dry food or empty oven.
  • The main PCB is defective.
  • The gas sensor is defective.
  • Wiring issue between the main PCB and the gas sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-14 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-21 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-21 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.

An E-21 Temperature Sensor Error will set if the control board detects The temperature sensor is open.

The most common issues that will cause an E-21 Temperature Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The temperature sensor is defective.
  • Wiring issue between the main PCB and the temperature sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-21 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-22 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-22 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.

An E-22 Temperature Sensor Error will set if the control board detects The temperature sensor is shorted.

The most common issues that will cause an E-22 Temperature Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The temperature sensor is defective.
  • Wiring issue between the main PCB and the temperature sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-22 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-23 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-23 fault code, it is indicating a Preheating Time Error has been detected by the internal self diagnostics system.

An E-23 Preheating Time Error will set if the control board detects The oven cooking temperature cannot reach the desired preheat setting within 30 minutes.

The most common issues that will cause an E-23 Preheating Time Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The temperature sensor is defective.
  • The heater is defective.
  • Wiring issue between the main PCB and the temperature sensor or heater circuit.

Try turning the Microwave main power supply off for 1 minute. If the E-23 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-24 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-24 fault code, it is indicating a Over Temperature Error has been detected by the internal self diagnostics system.

An E-24 Over Temperature Error will set if the control board detects The oven temperature is higher than 500F ̊F(265 ̊c) while oven is working.

The most common issues that will cause an E-24 Over Temperature Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The temperature sensor is defective.
  • Wiring issue between the main PCB and the temperature sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-24 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-25 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-25 fault code, it is indicating a Abnormal Temperature Error has been detected by the internal self diagnostics system.

An E-25 Abnormal Temperature Error will set if the control board detects An abnormal temperature is detected while the oven is on.

The most common issues that will cause an E-25 Abnormal Temperature Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The temperature sensor is defective.
  • Wiring issue between the main PCB and the temperature sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-25 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-26 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-26 fault code, it is indicating a Heating Error has been detected by the internal self diagnostics system.

An E-26 Heating Error will set if the control board detects An over temperature error occurred within the first 3 minutes of cooking but did not exceed the high limit temperature.

The most common issues that will cause an E-26 Heating Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The temperature sensor is defective.
  • The heater is defective.
  • Wiring issue between the main PCB and the temperature sensor or heater circuit.

Try turning the Microwave main power supply off for 1 minute. If the E-26 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-31 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-31 fault code, it is indicating a Weight Sensor Error has been detected by the internal self diagnostics system.

An E-31 Weight Sensor Error will set if the control board detects The weight sensor is open.

The most common issues that will cause an E-31 Weight Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The weight sensor is defective.
  • Wiring issue between the main PCB and the weight sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-31 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-32 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-32 fault code, it is indicating a Weight Sensor Error has been detected by the internal self diagnostics system.

An E-32 Weight Sensor Error will set if the control board detects The weight sensor is shorted.

The most common issues that will cause an E-32 Weight Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The weight sensor is defective.
  • Wiring issue between the main PCB and the weight sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-32 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-33 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-33 fault code, it is indicating a Weight Sensor Error has been detected by the internal self diagnostics system.

An E-33 Weight Sensor Error will set if the control board detects The weight sensor reading is abnormal.

The most common issues that will cause an E-33 Weight Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The weight sensor is defective.
  • Wiring issue between the main PCB and the weight sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-33 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-34 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-34 fault code, it is indicating a Weight Sensor Error has been detected by the internal self diagnostics system.

An E-34 Weight Sensor Error will set if the control board detects The weight sensor reading is abnormal.

The most common issues that will cause an E-34 Weight Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The weight sensor is defective.
  • Wiring issue between the main PCB and the weight sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-34 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-35 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-35 fault code, it is indicating a Weight Sensor Error has been detected by the internal self diagnostics system.

An E-35 Weight Sensor Error will set if the control board detects The weight sensor reading is abnormal.

The most common issues that will cause an E-35 Weight Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The weight sensor is defective.
  • Wiring issue between the main PCB and the weight sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-35 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-36 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-36 fault code, it is indicating a Door Open Error has been detected by the internal self diagnostics system.

An E-36 Door Open Error will set if the control board detects The door is open during operation.

The most common issues that will cause an E-36 Door Open Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The door switch is defective.
  • The door latch is defective.
  • Wiring issue between the main PCB and the door switch.

Try turning the Microwave main power supply off for 1 minute. If the E-36 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-41 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-41 fault code, it is indicating a Easy/Ph Sensor Error has been detected by the internal self diagnostics system.

An E-41 Easy/Ph Sensor Error will set if the control board detects The easy/ph sensor is open.

The most common issues that will cause an E-41 Easy/Ph Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The sensor is defective.
  • Wiring issue between the main PCB and the sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-41 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-42 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-42 fault code, it is indicating a Easy/Ph Sensor Error has been detected by the internal self diagnostics system.

An E-42 Easy/Ph Sensor Error will set if the control board detects The easy/ph sensor is open.

The most common issues that will cause an E-42 Easy/Ph Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The sensor is defective.
  • Wiring issue between the main PCB and the sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-42 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-43 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-43 fault code, it is indicating a Easy/Ph Sensor Error has been detected by the internal self diagnostics system.

An E-43 Easy/Ph Sensor Error will set if the control board detects The easy/ph sensor reading is abnormal.

The most common issues that will cause an E-43 Easy/Ph Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The sensor is defective.
  • Wiring issue between the main PCB and the sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-43 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-44 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-44 fault code, it is indicating a Gas Sensor Error has been detected by the internal self diagnostics system.

An E-44 Gas Sensor Error will set if the control board detects Dry up or no load error.

The most common issues that will cause an E-44 Gas Sensor Error to display on a Samsung Microwave are:

  • Dry food or empty oven.
  • The main PCB is defective.
  • The gas sensor is defective.
  • Wiring issue between the main PCB and the gas sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-44 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-45 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-45 fault code, it is indicating a Cool Error has been detected by the internal self diagnostics system.

An E-45 Cool Error will set if the control board detects There is no temperature change 3 minutes after cycle starts.

The most common issues that will cause an E-45 Cool Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The gas sensor is defective.
  • Wiring issue between the main PCB and the gas sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-45 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-46 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-46 fault code, it is indicating a Time Out Error has been detected by the internal self diagnostics system.

An E-46 Time Out Error will set if the control board detects The primary circuit is open for more than 3 Minutes. Check sensor, or defective PCB.

The most common issues that will cause an E-46 Time Out Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The sensor is defective.
  • Wiring issue.

Try turning the Microwave main power supply off for 1 minute. If the E-46 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-47 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-47 fault code, it is indicating a Door Open Error has been detected by the internal self diagnostics system.

An E-47 Door Open Error will set if the control board detects The door is open during operation.

The most common issues that will cause an E-47 Door Open Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The door switch is defective.
  • The door latch is defective.
  • Wiring issue between the main PCB and the door switch.

Try turning the Microwave main power supply off for 1 minute. If the E-47 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-51 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-51 fault code, it is indicating a EEPROM Error has been detected by the internal self diagnostics system.

An E-51 EEPROM Error will set if the control board detects EEPROM Open Error

The most common issues that will cause an E-51 EEPROM Error to display on a Samsung Microwave are:

  • The main PCB is defective.

Try turning the Microwave main power supply off for 1 minute. If the E-51 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-53 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-53 fault code, it is indicating a EEPROM Error has been detected by the internal self diagnostics system.

An E-53 EEPROM Error will set if the control board detects EEPROM Format Error

The most common issues that will cause an E-53 EEPROM Error to display on a Samsung Microwave are:

  • The main PCB is defective.

Try turning the Microwave main power supply off for 1 minute. If the E-53 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-54 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-54 fault code, it is indicating a EEPROM Error has been detected by the internal self diagnostics system.

An E-54 EEPROM Error will set if the control board detects EEPROM Reset Error

The most common issues that will cause an E-54 EEPROM Error to display on a Samsung Microwave are:

  • The main PCB is defective.

Try turning the Microwave main power supply off for 1 minute. If the E-54 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-61 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-61 fault code, it is indicating a Humidity Sensor Error has been detected by the internal self diagnostics system.

An E-61 Humidity Sensor Error will set if the control board detects The humidity sensor is open.

The most common issues that will cause an E-61 Humidity Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The humidity sensor is defective.
  • Wiring issue between the main PCB and the humidity sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-61 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-62 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-62 fault code, it is indicating a Humidity Sensor Error has been detected by the internal self diagnostics system.

An E-62 Humidity Sensor Error will set if the control board detects The humidity sensor is shorted.

The most common issues that will cause an E-62 Humidity Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The humidity sensor is defective.
  • Wiring issue between the main PCB and the humidity sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-62 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-63 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-63 fault code, it is indicating a Humidity Sensor Error has been detected by the internal self diagnostics system.

An E-63 Humidity Sensor Error will set if the control board detects The humidity sensor reading is abnormal.

The most common issues that will cause an E-63 Humidity Sensor Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The humidity sensor is defective.
  • Wiring issue between the main PCB and the humidity sensor.

Try turning the Microwave main power supply off for 1 minute. If the E-63 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-83 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-83 fault code, it is indicating a Communication Error has been detected by the internal self diagnostics system.

An E-83 Communication Error will set if the control board detects There is a communication error between the main PCB and the touch PCB.

The most common issues that will cause an E-83 Communication Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The touch PCB is defective.
  • Wiring issue between the main PCB and the sub PCB.

Try turning the Microwave main power supply off for 1 minute. If the E-83 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E-A1 mean on a Samsung Microwave?

If your Samsung Microwave is displaying an E-A1 fault code, it is indicating a Damper Error has been detected by the internal self diagnostics system.

An E-A1 Damper Error will set if the control board detects The damper has not reached the desired position within 40 seconds.

The most common issues that will cause an E-A1 Damper Error to display on a Samsung Microwave are:

  • The main PCB is defective.
  • The damper motor is defective.
  • The damper switch is defective.
  • Wiring issue between the main PCB and the damper motor or switch.

Try turning the Microwave main power supply off for 1 minute. If the E-A1 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does SE mean on a Samsung Microwave?

If your Samsung Microwave is displaying an SE fault code, it is indicating a Shorted Key Error has been detected by the internal self diagnostics system.

An SE Shorted Key Error will set if the control board detects Any button is stuck or held for more than 10 seconds.

The most common issues that will cause an SE Shorted Key Error to display on a Samsung Microwave are:

  • The keypad is defective.
  • The microwave control PCB is defective.
  • Wiring issue between the keypad and the control PCB.

Try turning the Microwave main power supply off for 1 minute. If the SE code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does TE mean on a Samsung Microwave?

If your Samsung Microwave is displaying an TE fault code, it is indicating a Touch Key Error has been detected by the internal self diagnostics system.

An TE Touch Key Error will set if the control board detects Any button is stuck or held for more than 10 seconds.

The most common issues that will cause an TE Touch Key Error to display on a Samsung Microwave are:

  • The keypad is defective.
  • The microwave control PCB is defective.
  • Wiring issue between the keypad and the control PCB.

Try turning the Microwave main power supply off for 1 minute. If the TE code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

Samsung Microwave Error Codes Disclaimer

The Samsung Microwave Error Codes information contained on this page is provided for informational purposes only. ApplianceFaultCodes.com does not guarantee the information to be correct or give a proper diagnosis of any appliance. Always take proper safety precautions when installing or repairing any major appliance.