GE Dishwasher Error Codes - Appliance Fault Codes

The first thing to try is switching the Dishwasher main power supply off for 60 seconds. This usual only works if the fault was set due to a supply voltage fluctuation from a storm or power outage. It may also work if the problem is intermittent. Unfortunately this might only be a short term solution because if the problem is intermittent and the fault returns, the error code will display again.

If that doesn’t work, the problem triggering the error code will need to be repaired in order to clear the fault code.

Why is my GE Dishwasher not working?

Some GE Dishwasher error codes will disable the appliance from operating. The error code will need to be resolved in order for the appliance to function normally again.

What does 1-24H mean on a GE Dishwasher?

If your GE Dishwasher is displaying an 1-24H fault code, it is indicating a Delay Start has been detected by the internal self diagnostics system.

An 1-24H Delay Start will set if the control board detects The dishwasher is in delay start mode.

The most common issues that will cause an 1-24H Delay Start to display on a GE Dishwasher are:

Press the delay start button until the delay is at the desired time or off.

Try turning the Dishwasher main power supply off for 1 minute. If the 1-24H code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does 999 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an 999 fault code, it is indicating a Water Leak Error has been detected by the internal self diagnostics system.

An 999 Water Leak Error will set if the control board detects Water has accumulated in the bottom leak tray under the dishwasher.

The most common issues that will cause an 999 Water Leak Error to display on a GE Dishwasher are:

Over sud issue due to the wrong type of detergent being used.
The dishwasher is not level.
The door is not closing properly.
The flood sensor micro switch is defective.
The pressure sensor is defective.
The main PCB is defective.
The drain pump is jammed or defective.
The dishwasher is overfilling.
The inlet valve is leaking.
The sump is leaking.
The wash pump is leaking.
A hose is leaking.
The drain hose is plugged.

Try turning the Dishwasher main power supply off for 1 minute. If the 999 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does C1 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an C1 fault code, it is indicating a Drain Error has been detected by the internal self diagnostics system.

An C1 Drain Error will set if the control board detects Dishwasher drain time has exceeded 2 minutes.

The most common issues that will cause an C1 Drain Error to display on a GE Dishwasher are:

The drain pump is defective.
The drain is plugged

Try turning the Dishwasher main power supply off for 1 minute. If the C1 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does C2 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an C2 fault code, it is indicating a Drain Error has been detected by the internal self diagnostics system.

An C2 Drain Error will set if the control board detects Dishwasher drain time has exceeded 7 minutes.

The most common issues that will cause an C2 Drain Error to display on a GE Dishwasher are:

The drain pump is defective.
The drain is plugged

Try turning the Dishwasher main power supply off for 1 minute. If the C2 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does C3 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an C3 fault code, it is indicating a Drain Error has been detected by the internal self diagnostics system.

An C3 Drain Error will set if the control board detects The dishwasher will not drain

The most common issues that will cause an C3 Drain Error to display on a GE Dishwasher are:

The drain pump is defective.
The drain is plugged

Try turning the Dishwasher main power supply off for 1 minute. If the C3 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does C4 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an C4 fault code, it is indicating a Drain Error has been detected by the internal self diagnostics system.

An C4 Drain Error will set if the control board detects Machine filled twice after a power failure.

The most common issues that will cause an C4 Drain Error to display on a GE Dishwasher are:

The water level float is stuck or defective.
The drain pump is defective.
The drain is plugged

Try turning the Dishwasher main power supply off for 1 minute. If the C4 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does C5 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an C5 fault code, it is indicating a Drain Error has been detected by the internal self diagnostics system.

An C5 Drain Error will set if the control board detects The pump out time is too short.

The most common issues that will cause an C5 Drain Error to display on a GE Dishwasher are:

The water level float is stuck or defective.
The inlet valve is defective.
There is no water supplied to the dishwasher

Try turning the Dishwasher main power supply off for 1 minute. If the C5 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does C6 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an C6 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.

An C6 Temperature Sensor Error will set if the control board detects The temperature sensor is open or shorted.

The most common issues that will cause an C6 Temperature Sensor Error to display on a GE Dishwasher are:

The inlet water temperature is to high or low.
The thermistor is defective.
The main PCB is defective.
Wiring issue between the thermistor and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the C6 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does C7 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an C7 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.

An C7 Temperature Sensor Error will set if the control board detects The temperature sensor is open or shorted.

The most common issues that will cause an C7 Temperature Sensor Error to display on a GE Dishwasher are:

The inlet water temperature is to high or low.
The thermistor is defective.
The main PCB is defective.
Wiring issue between the thermistor and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the C7 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does C8 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an C8 fault code, it is indicating a Dispenser Error has been detected by the internal self diagnostics system.

An C8 Dispenser Error will set if the control board detects This display indicates that the detergent dispenser is blocked from opening fully.

The most common issues that will cause an C8 Dispenser Error to display on a GE Dishwasher are:

Something is blocking the dispenser door.

Try turning the Dishwasher main power supply off for 1 minute. If the C8 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does Cup Open mean on a GE Dishwasher?

If your GE Dishwasher is displaying an Cup Open fault code, it is indicating a Dispenser Error has been detected by the internal self diagnostics system.

An Cup Open Dispenser Error will set if the control board detects The detergent cup has not been closed. It’s a reminder to add detergent and latch the cup closed.

The most common issues that will cause an Cup Open Dispenser Error to display on a GE Dishwasher are:

The detergent dispenser is open.
The detergent dispenser is defective.
The main PCB is defective.
Wiring issue between the detergent dispenser and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the Cup Open code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E1 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an E1 fault code, it is indicating a Water Inlet Error has been detected by the internal self diagnostics system.

An E1 Water Inlet Error will set if the control board detects During the water intake step, the flow meter did not detect the defined amount of water entering the dishwasher after 4 minutes.

The most common issues that will cause an E1 Water Inlet Error to display on a GE Dishwasher are:

Low water supply to the dishwasher.
The inlet valve is defective.
The flow meter is defective.
The pressure switch is defective.
The main PCB is defective.
The drain hose is siphoning.

Try turning the Dishwasher main power supply off for 1 minute. If the E1 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E3 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an E3 fault code, it is indicating a Water Temperature Error has been detected by the internal self diagnostics system.

An E3 Water Temperature Error will set if the control board detects The water temperature can’t reach the defined value after 90 minutes. Only appears in the factory mode.

The most common issues that will cause an E3 Water Temperature Error to display on a GE Dishwasher are:

The heater is defective.
The thermistor is defective.
The main PCB is defective.

Try turning the Dishwasher main power supply off for 1 minute. If the E3 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E4 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an E4 fault code, it is indicating a Water Leak Error has been detected by the internal self diagnostics system.

An E4 Water Leak Error will set if the control board detects Water has accumulated in the bottom leak tray under the dishwasher.

The most common issues that will cause an E4 Water Leak Error to display on a GE Dishwasher are:

Over sud issue due to the wrong type of detergent being used.
The dishwasher is not level.
The door is not closing properly.
The flood sensor micro switch is defective.
The pressure sensor is defective.
The main PCB is defective.
The drain pump is jammed or defective.
The dishwasher is overfilling.
The inlet valve is leaking.
The sump is leaking.
The wash pump is leaking.
A hose is leaking.
The drain hose is plugged.

Try turning the Dishwasher main power supply off for 1 minute. If the E4 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E6 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an E6 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.

An E6 Temperature Sensor Error will set if the control board detects The temperature sensor is open. Only appears in the factory mode.

The most common issues that will cause an E6 Temperature Sensor Error to display on a GE Dishwasher are:

The inlet water temperature is to high or low.
The thermistor is defective.
The main PCB is defective.
Wiring issue between the thermistor and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the E6 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E7 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an E7 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.

An E7 Temperature Sensor Error will set if the control board detects The temperature sensor is shorted. Only appears in the factory mode.

The most common issues that will cause an E7 Temperature Sensor Error to display on a GE Dishwasher are:

The inlet water temperature is to high or low.
The thermistor is defective.
The main PCB is defective.
Wiring issue between the thermistor and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the E7 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E8 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an E8 fault code, it is indicating a Diverter Valve Error has been detected by the internal self diagnostics system.

An E8 Diverter Valve Error will set if the control board detects There is an issue with the diverter valve assembly.

The most common issues that will cause an E8 Diverter Valve Error to display on a GE Dishwasher are:

The diverter valve motor is jammed or defective.
The diverter valve position micro switch is defective.
The main PCB is defective.
Wiring issue between the diverter valve switch or motor and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the E8 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E9 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an E9 fault code, it is indicating a Stuck Button Error has been detected by the internal self diagnostics system.

An E9 Stuck Button Error will set if the control board detects A button is stuck or has been held down for more than 30 seconds.

The most common issues that will cause an E9 Stuck Button Error to display on a GE Dishwasher are:

A button is stuck or held.
The control panel is defective.

Try turning the Dishwasher main power supply off for 1 minute. If the E9 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does ED mean on a GE Dishwasher?

If your GE Dishwasher is displaying an ED fault code, it is indicating a Communication Error has been detected by the internal self diagnostics system.

An ED Communication Error will set if the control board detects The display board can’t receive any signal or the main board can’t send any signal for more than 20 seconds.

The most common issues that will cause an ED Communication Error to display on a GE Dishwasher are:

The display board is defective.
The main PCB is defective.
Wiring issue between the display board and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the ED code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F2 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F2 fault code, it is indicating a Communication Error has been detected by the internal self diagnostics system.

An F2 Communication Error will set if the control board detects The display board can’t receive any signal or the main board can’t send any signal for more than 20 seconds.

The most common issues that will cause an F2 Communication Error to display on a GE Dishwasher are:

The display board is defective.
The main PCB is defective.
Wiring issue between the display board and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F2 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F3 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F3 fault code, it is indicating a Configuration Error has been detected by the internal self diagnostics system.

An F3 Configuration Error will set if the control board detects The inverter is not found

The most common issues that will cause an F3 Configuration Error to display on a GE Dishwasher are:

The inverter is defective.
The main PCB is defective.
Wiring issue between the inverter and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F3 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F5 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F5 fault code, it is indicating a Communication Error has been detected by the internal self diagnostics system.

An F5 Communication Error will set if the control board detects Communication error between the inverter and main PCB.

The most common issues that will cause an F5 Communication Error to display on a GE Dishwasher are:

The inverter is defective.
The main PCB is defective.
Wiring issue between the inverter and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F5 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F6 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F6 fault code, it is indicating a Communication Error has been detected by the internal self diagnostics system.

An F6 Communication Error will set if the control board detects Communication lost with wireless module

The most common issues that will cause an F6 Communication Error to display on a GE Dishwasher are:

The wireless module is defective.
The main PCB is defective.
Wiring issue between the wireless module and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F6 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F16 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F16 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.

An F16 Temperature Sensor Error will set if the control board detects High Water Temperature.

The most common issues that will cause an F16 Temperature Sensor Error to display on a GE Dishwasher are:

The inlet water temperature is to high or low.
The thermistor is defective.
The main PCB is defective.
Wiring issue between the thermistor and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F16 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F33 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F33 fault code, it is indicating a Door Switch Error has been detected by the internal self diagnostics system.

An F33 Door Switch Error will set if the control board detects The signal from the door switch is abnormal.

The most common issues that will cause an F33 Door Switch Error to display on a GE Dishwasher are:

The door switch is defective.
The main PCB is defective.
Wiring issue between the door switch and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F33 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F34 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F34 fault code, it is indicating a Water Leak Error has been detected by the internal self diagnostics system.

An F34 Water Leak Error will set if the control board detects Water has accumulated in the bottom leak tray under the dishwasher.

The most common issues that will cause an F34 Water Leak Error to display on a GE Dishwasher are:

Over sud issue due to the wrong type of detergent being used.
The dishwasher is not level.
The door is not closing properly.
The flood sensor micro switch is defective.
The pressure sensor is defective.
The main PCB is defective.
The drain pump is jammed or defective.
The dishwasher is overfilling.
The inlet valve is leaking.
The sump is leaking.
The wash pump is leaking.
A hose is leaking.
The drain hose is plugged.

Try turning the Dishwasher main power supply off for 1 minute. If the F34 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F35 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F35 fault code, it is indicating a Diverter Valve Error has been detected by the internal self diagnostics system.

An F35 Diverter Valve Error will set if the control board detects There is an issue with the diverter valve assembly.

The most common issues that will cause an F35 Diverter Valve Error to display on a GE Dishwasher are:

The diverter valve motor is jammed or defective.
The diverter valve position micro switch is defective.
The main PCB is defective.
Wiring issue between the diverter valve switch or motor and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F35 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F36 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F36 fault code, it is indicating a CSM Error has been detected by the internal self diagnostics system.

An F36 CSM Error will set if the control board detects The Current Sense Module has tripped.

The most common issues that will cause an F36 CSM Error to display on a GE Dishwasher are:

Activate service mode to reset CMS
Possible current leakage to ground

Try turning the Dishwasher main power supply off for 1 minute. If the F36 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F48 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F48 fault code, it is indicating a Turbidity Sensor Error has been detected by the internal self diagnostics system.

An F48 Turbidity Sensor Error will set if the control board detects The turbidity sensor signal is high.

The most common issues that will cause an F48 Turbidity Sensor Error to display on a GE Dishwasher are:

The turbidity sensor is defective.
The main PCB is defective.
Wiring issue between the turbidity sensor and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F48 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F49 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F49 fault code, it is indicating a Turbidity Sensor Error has been detected by the internal self diagnostics system.

An F49 Turbidity Sensor Error will set if the control board detects The turbidity sensor signal is low.

The most common issues that will cause an F49 Turbidity Sensor Error to display on a GE Dishwasher are:

The turbidity sensor is defective.
The main PCB is defective.
Wiring issue between the turbidity sensor and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F49 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F50 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F50 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.

An F50 Temperature Sensor Error will set if the control board detects The temperature sensor is open or shorted.

The most common issues that will cause an F50 Temperature Sensor Error to display on a GE Dishwasher are:

The inlet water temperature is to high or low.
The thermistor is defective.
The main PCB is defective.
Wiring issue between the thermistor and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F50 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F51 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F51 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.

An F51 Temperature Sensor Error will set if the control board detects The temperature sensor is open or shorted.

The most common issues that will cause an F51 Temperature Sensor Error to display on a GE Dishwasher are:

The inlet water temperature is to high or low.
The thermistor is defective.
The main PCB is defective.
Wiring issue between the thermistor and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F51 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F52 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F52 fault code, it is indicating a Turbidity Sensor Error has been detected by the internal self diagnostics system.

An F52 Turbidity Sensor Error will set if the control board detects .Turbidity sensor calibration failure.

The most common issues that will cause an F52 Turbidity Sensor Error to display on a GE Dishwasher are:

The turbidity sensor is defective.
The main PCB is defective.
Wiring issue between the turbidity sensor and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F52 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F64 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F64 fault code, it is indicating a Inverter Error has been detected by the internal self diagnostics system.

An F64 Inverter Error will set if the control board detects The inverter has an error.

The most common issues that will cause an F64 Inverter Error to display on a GE Dishwasher are:

The inverter is defective.
The main PCB is defective.
Wiring issue between the inverter and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F64 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F65 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F65 fault code, it is indicating a Inverter Error has been detected by the internal self diagnostics system.

An F65 Inverter Error will set if the control board detects No water detected

The most common issues that will cause an F65 Inverter Error to display on a GE Dishwasher are:

The dishwasher did not fill.
The inverter is defective.
The main PCB is defective.
Wiring issue between the inverter and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F65 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F80 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F80 fault code, it is indicating a Turbidity Sensor Error has been detected by the internal self diagnostics system.

An F80 Turbidity Sensor Error will set if the control board detects No water flow is detected by the turbidity sensor.

The most common issues that will cause an F80 Turbidity Sensor Error to display on a GE Dishwasher are:

There is no water flow in the dishwasher.
The turbidity sensor is defective.
The main PCB is defective.
Wiring issue between the turbidity sensor and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F80 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F96 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F96 fault code, it is indicating a Turbidity Sensor Error has been detected by the internal self diagnostics system.

An F96 Turbidity Sensor Error will set if the control board detects No water in the tub is detected by the turbidity sensor.

The most common issues that will cause an F96 Turbidity Sensor Error to display on a GE Dishwasher are:

There is no water in the dishwasher tub.
The turbidity sensor is defective.
The main PCB is defective.
Wiring issue between the turbidity sensor and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F96 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F97 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F97 fault code, it is indicating a Water Temperature Error has been detected by the internal self diagnostics system.

An F97 Water Temperature Error will set if the control board detects The water temperature can’t reach the defined value.

The most common issues that will cause an F97 Water Temperature Error to display on a GE Dishwasher are:

The heater is defective.
The thermistor is defective.
The main PCB is defective.

Try turning the Dishwasher main power supply off for 1 minute. If the F97 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F98 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F98 fault code, it is indicating a Turbidity Sensor Error has been detected by the internal self diagnostics system.

An F98 Turbidity Sensor Error will set if the control board detects No water draining is detected by the turbidity sensor.

The most common issues that will cause an F98 Turbidity Sensor Error to display on a GE Dishwasher are:

The dishwasher is not draining properly.
The turbidity sensor is defective.
The main PCB is defective.
Wiring issue between the turbidity sensor and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F98 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F99 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F99 fault code, it is indicating a Water Temperature Error has been detected by the internal self diagnostics system.

An F99 Water Temperature Error will set if the control board detects The water temperature can’t reach the defined value.

The most common issues that will cause an F99 Water Temperature Error to display on a GE Dishwasher are:

The heater is defective.
The thermistor is defective.
The main PCB is defective.

Try turning the Dishwasher main power supply off for 1 minute. If the F99 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F112 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F112 fault code, it is indicating a Stuck Button Error has been detected by the internal self diagnostics system.

An F112 Stuck Button Error will set if the control board detects A button is stuck or has been held down.

The most common issues that will cause an F112 Stuck Button Error to display on a GE Dishwasher are:

A button is stuck or held.
The control panel is defective.

Try turning the Dishwasher main power supply off for 1 minute. If the F112 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F128 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F128 fault code, it is indicating a Rinse Aid Error has been detected by the internal self diagnostics system.

An F128 Rinse Aid Error will set if the control board detects The rinse aid dispenser level is low.

The most common issues that will cause an F128 Rinse Aid Error to display on a GE Dishwasher are:

Fill the rinse aid dispenser.

Try turning the Dishwasher main power supply off for 1 minute. If the F128 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F144 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F144 fault code, it is indicating a Inverter Error has been detected by the internal self diagnostics system.

An F144 Inverter Error will set if the control board detects There is an internal inverter issue.

The most common issues that will cause an F144 Inverter Error to display on a GE Dishwasher are:

The inverter is defective.

Try turning the Dishwasher main power supply off for 1 minute. If the F144 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F145 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F145 fault code, it is indicating a Inverter Error has been detected by the internal self diagnostics system.

An F145 Inverter Error will set if the control board detects AC Voltage to the Inverter is abnormal.

The most common issues that will cause an F145 Inverter Error to display on a GE Dishwasher are:

The inverter is defective.
AC supply voltage issue.

Try turning the Dishwasher main power supply off for 1 minute. If the F145 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F146 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F146 fault code, it is indicating a Circulation Pump Error has been detected by the internal self diagnostics system.

An F146 Circulation Pump Error will set if the control board detects The circulation pump amperage draw is abnormal.

The most common issues that will cause an F146 Circulation Pump Error to display on a GE Dishwasher are:

The circulation pump is defective.
The circulation pump wire harness is defective.

Try turning the Dishwasher main power supply off for 1 minute. If the F146 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F147 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F147 fault code, it is indicating a Drain Pump Error has been detected by the internal self diagnostics system.

An F147 Drain Pump Error will set if the control board detects The drain pump amperage draw is abnormal.

The most common issues that will cause an F147 Drain Pump Error to display on a GE Dishwasher are:

The drain pump is defective.
The drain pump wire harness is defective.

Try turning the Dishwasher main power supply off for 1 minute. If the F147 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F148 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F148 fault code, it is indicating a Pump Error has been detected by the internal self diagnostics system.

An F148 Pump Error will set if the control board detects The drain or circulation pump has blown the thermal cut out.

The most common issues that will cause an F148 Pump Error to display on a GE Dishwasher are:

The drain pump is defective.
The circulation pump is defective.

Try turning the Dishwasher main power supply off for 1 minute. If the F148 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F149 mean on a GE Dishwasher?

If your GE Dishwasher is displaying an F149 fault code, it is indicating a Inverter Error has been detected by the internal self diagnostics system.

An F149 Inverter Error will set if the control board detects The inverter has an error.

The most common issues that will cause an F149 Inverter Error to display on a GE Dishwasher are:

The inverter is defective.
The main PCB is defective.
Wiring issue between the inverter and the main PCB

Try turning the Dishwasher main power supply off for 1 minute. If the F149 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does H2O mean on a GE Dishwasher?

If your GE Dishwasher is displaying an H2O fault code, it is indicating a Water Inlet Error has been detected by the internal self diagnostics system.

An H2O Water Inlet Error will set if the control board detects Low water level detected.

The most common issues that will cause an H2O Water Inlet Error to display on a GE Dishwasher are:

Low water supply to the dishwasher.
The inlet valve is defective.
The flow meter is defective.
The pressure switch is defective.
The main PCB is defective.
The drain hose is siphoning.

Try turning the Dishwasher main power supply off for 1 minute. If the H2O code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does LEAK DETECTED mean on a GE Dishwasher?

If your GE Dishwasher is displaying an LEAK DETECTED fault code, it is indicating a Water Leak Error has been detected by the internal self diagnostics system.

An LEAK DETECTED Water Leak Error will set if the control board detects Water has accumulated in the bottom leak tray under the dishwasher.

The most common issues that will cause an LEAK DETECTED Water Leak Error to display on a GE Dishwasher are:

Over sud issue due to the wrong type of detergent being used.
The dishwasher is not level.
The door is not closing properly.
The flood sensor micro switch is defective.
The pressure sensor is defective.
The main PCB is defective.
The drain pump is jammed or defective.
The dishwasher is overfilling.
The inlet valve is leaking.
The sump is leaking.
The wash pump is leaking.
A hose is leaking.
The drain hose is plugged.

Try turning the Dishwasher main power supply off for 1 minute. If the LEAK DETECTED code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does PF mean on a GE Dishwasher?

If your GE Dishwasher is displaying an PF fault code, it is indicating a Power Failure has been detected by the internal self diagnostics system.

An PF Power Failure will set if the control board detects Indicates that there has been a power failure to dishwasher.

The most common issues that will cause an PF Power Failure to display on a GE Dishwasher are:

Select the desired cycle and options, press the start pad and the dishwasher will function normally.

Try turning the Dishwasher main power supply off for 1 minute. If the PF code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

GE Dishwasher Error Codes Disclaimer

The GE Dishwasher Error Codes information contained on this page is provided for informational purposes only. ApplianceFaultCodes.com does not guarantee the information to be correct or give a proper diagnosis of any appliance. Always take proper safety precautions when installing or repairing any major appliance.