Select form the list of GE Oven error codes below for the code meaning and possible issues that may be causing the fault to display.
The GE Oven error codes listed above may also apply to the following brands.
- Haier Oven Error Codes.
- Hotpoint Oven Error Codes.
- Moffat Oven Error Codes.
Why is my GE Oven displaying error codes?
Your GE Oven will display error codes when the main control panel internal diagnostics system has detected a problem.
How can I reset GE Oven Error Codes
The first thing to try is switching the Oven main power supply off for 60 seconds. This usual only works if the fault was set due to a supply voltage fluctuation from a storm or power outage. It may also work if the problem is intermittent. Unfortunately this might only be a short term solution because if the problem is intermittent and the fault returns, the error code will display again.
If that doesn’t work, the problem triggering the error code will need to be repaired in order to clear the fault code.
Why is my GE Oven not working?
Some GE Oven error codes will disable the appliance from operating. The error code will need to be resolved in order for the appliance to function normally again.
What does 100 mean on a GE Oven?
If your GE Oven is displaying an 100 fault code, it is indicating a Supply Voltage Error has been detected by the internal self diagnostics system.
An 100 Supply Voltage Error will set if the control board detects The power supply voltage is too high or too low.
The most common issues that will cause an 100 Supply Voltage Error to display on a GE Oven are:
- The power supply is miswired.
- The power supply voltage is too high.
- The power supply voltage is too low.
- The control board is defective.
Try turning the Oven main power supply off for 1 minute. If the 100 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 200 mean on a GE Oven?
If your GE Oven is displaying an 200 fault code, it is indicating a Oven Control Error has been detected by the internal self diagnostics system.
An 200 Oven Control Error will set if the control board detects Upper or single oven runaway temp (615F), door unlocked.
The most common issues that will cause an 200 Oven Control Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the 200 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 210 mean on a GE Oven?
If your GE Oven is displaying an 210 fault code, it is indicating a Oven Control Error has been detected by the internal self diagnostics system.
An 210 Oven Control Error will set if the control board detects Upper or single oven runaway temp (930F), door locked.
The most common issues that will cause an 210 Oven Control Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the 210 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 220 mean on a GE Oven?
If your GE Oven is displaying an 220 fault code, it is indicating a Oven Control Error has been detected by the internal self diagnostics system.
An 220 Oven Control Error will set if the control board detects Lower oven runaway temp (615F), door unlocked.
The most common issues that will cause an 220 Oven Control Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the 220 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 230 mean on a GE Oven?
If your GE Oven is displaying an 230 fault code, it is indicating a Oven Control Error has been detected by the internal self diagnostics system.
An 230 Oven Control Error will set if the control board detects Lower oven runaway temp (930F), door locked.
The most common issues that will cause an 230 Oven Control Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the 230 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 300 mean on a GE Oven?
If your GE Oven is displaying an 300 fault code, it is indicating a Oven Temperature Sensor Error has been detected by the internal self diagnostics system.
An 300 Oven Temperature Sensor Error will set if the control board detects The lower or single oven temperature sensor is shorted.
The most common issues that will cause an 300 Oven Temperature Sensor Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the 300 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 310 mean on a GE Oven?
If your GE Oven is displaying an 310 fault code, it is indicating a Oven Temperature Sensor Error has been detected by the internal self diagnostics system.
An 310 Oven Temperature Sensor Error will set if the control board detects The lower or single oven temperature sensor is open.
The most common issues that will cause an 310 Oven Temperature Sensor Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the 310 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 320 mean on a GE Oven?
If your GE Oven is displaying an 320 fault code, it is indicating a Oven Temperature Sensor Error has been detected by the internal self diagnostics system.
An 320 Oven Temperature Sensor Error will set if the control board detects The upper oven temperature sensor is shorted.
The most common issues that will cause an 320 Oven Temperature Sensor Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the 320 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 330 mean on a GE Oven?
If your GE Oven is displaying an 330 fault code, it is indicating a Oven Temperature Sensor Error has been detected by the internal self diagnostics system.
An 330 Oven Temperature Sensor Error will set if the control board detects The upper oven temperature sensor is open.
The most common issues that will cause an 330 Oven Temperature Sensor Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the 330 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 340 mean on a GE Oven?
If your GE Oven is displaying an 340 fault code, it is indicating a Probe Error has been detected by the internal self diagnostics system.
An 340 Probe Error will set if the control board detects The lower or single oven meat probe is shorted.
The most common issues that will cause an 340 Probe Error to display on a GE Oven are:
- The probe is defective.
- The oven control PCB is defective.
- Wiring issue between the probe and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the 340 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 342 mean on a GE Oven?
If your GE Oven is displaying an 342 fault code, it is indicating a Probe Error has been detected by the internal self diagnostics system.
An 342 Probe Error will set if the control board detects The upper oven meat probe is shorted.
The most common issues that will cause an 342 Probe Error to display on a GE Oven are:
- The probe is defective.
- The oven control PCB is defective.
- Wiring issue between the probe and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the 342 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 350 mean on a GE Oven?
If your GE Oven is displaying an 350 fault code, it is indicating a Cooling Fan Error has been detected by the internal self diagnostics system.
An 350 Cooling Fan Error will set if the control board detects The cooling fan speed is too slow.
The most common issues that will cause an 350 Cooling Fan Error to display on a GE Oven are:
- The oven fan motor is defective.
- The oven fan motor is blocked.
- The oven control PCB is defective.
- Wiring issue between the oven fan motor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the 350 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 351 mean on a GE Oven?
If your GE Oven is displaying an 351 fault code, it is indicating a Cooling Fan Error has been detected by the internal self diagnostics system.
An 351 Cooling Fan Error will set if the control board detects The cooling fan is turning when commanded off.
The most common issues that will cause an 351 Cooling Fan Error to display on a GE Oven are:
- The oven control PCB is defective.
- Wiring issue between the oven fan motor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the 351 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 352 mean on a GE Oven?
If your GE Oven is displaying an 352 fault code, it is indicating a Cooling Fan Error has been detected by the internal self diagnostics system.
An 352 Cooling Fan Error will set if the control board detects Cooling Fan Error
The most common issues that will cause an 352 Cooling Fan Error to display on a GE Oven are:
The cooling fan speed is too slow.Try turning the Oven main power supply off for 1 minute. If the 352 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 400 mean on a GE Oven?
If your GE Oven is displaying an 400 fault code, it is indicating a Over Temperature Error has been detected by the internal self diagnostics system.
An 400 Over Temperature Error will set if the control board detects The temperature of the cooktop is to high.
The most common issues that will cause an 400 Over Temperature Error to display on a GE Oven are:
- The temperature sensor is defective.
- The Induction Power System is defective.
- Wiring issue between the top sensor and the Induction Power System.
- Ventilation issue..
Try turning the Oven main power supply off for 1 minute. If the 400 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 401 mean on a GE Oven?
If your GE Oven is displaying an 401 fault code, it is indicating a Over Temperature Error has been detected by the internal self diagnostics system.
An 401 Over Temperature Error will set if the control board detects The temperature of the cooktop is to high.
The most common issues that will cause an 401 Over Temperature Error to display on a GE Oven are:
- The temperature sensor is defective.
- The Induction Power System is defective.
- Wiring issue between the top sensor and the Induction Power System.
- Ventilation issue..
Try turning the Oven main power supply off for 1 minute. If the 401 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 402 mean on a GE Oven?
If your GE Oven is displaying an 402 fault code, it is indicating a Over Temperature Error has been detected by the internal self diagnostics system.
An 402 Over Temperature Error will set if the control board detects The temperature of the cooktop is to high.
The most common issues that will cause an 402 Over Temperature Error to display on a GE Oven are:
- The temperature sensor is defective.
- The Induction Power System is defective.
- Wiring issue between the top sensor and the Induction Power System.
- Ventilation issue..
Try turning the Oven main power supply off for 1 minute. If the 402 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 403 mean on a GE Oven?
If your GE Oven is displaying an 403 fault code, it is indicating a Over Temperature Error has been detected by the internal self diagnostics system.
An 403 Over Temperature Error will set if the control board detects The temperature of the cooktop is to high.
The most common issues that will cause an 403 Over Temperature Error to display on a GE Oven are:
- The temperature sensor is defective.
- The Induction Power System is defective.
- Wiring issue between the top sensor and the Induction Power System.
- Ventilation issue..
Try turning the Oven main power supply off for 1 minute. If the 403 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 410 mean on a GE Oven?
If your GE Oven is displaying an 410 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.
An 410 Temperature Sensor Error will set if the control board detects The temperature Sensor is out of range.
The most common issues that will cause an 410 Temperature Sensor Error to display on a GE Oven are:
- The temperature sensor is defective.
- The Induction Power System is defective.
- Wiring issue between the temperature sensor / coil and the Induction Power System.
Try turning the Oven main power supply off for 1 minute. If the 410 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 411 mean on a GE Oven?
If your GE Oven is displaying an 411 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.
An 411 Temperature Sensor Error will set if the control board detects The temperature Sensor is out of range.
The most common issues that will cause an 411 Temperature Sensor Error to display on a GE Oven are:
- The temperature sensor is defective.
- The Induction Power System is defective.
- Wiring issue between the temperature sensor / coil and the Induction Power System.
Try turning the Oven main power supply off for 1 minute. If the 411 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 412 mean on a GE Oven?
If your GE Oven is displaying an 412 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.
An 412 Temperature Sensor Error will set if the control board detects The temperature Sensor is out of range.
The most common issues that will cause an 412 Temperature Sensor Error to display on a GE Oven are:
- The temperature sensor is defective.
- The Induction Power System is defective.
- Wiring issue between the temperature sensor / coil and the Induction Power System.
Try turning the Oven main power supply off for 1 minute. If the 412 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 413 mean on a GE Oven?
If your GE Oven is displaying an 413 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.
An 413 Temperature Sensor Error will set if the control board detects The temperature Sensor is out of range.
The most common issues that will cause an 413 Temperature Sensor Error to display on a GE Oven are:
- The temperature sensor is defective.
- The Induction Power System is defective.
- Wiring issue between the temperature sensor / coil and the Induction Power System.
Try turning the Oven main power supply off for 1 minute. If the 413 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 420 mean on a GE Oven?
If your GE Oven is displaying an 420 fault code, it is indicating a Induction Coil Error has been detected by the internal self diagnostics system.
An 420 Induction Coil Error will set if the control board detects The induction coil is open.
The most common issues that will cause an 420 Induction Coil Error to display on a GE Oven are:
- The induction coil is defective.
- The Induction Power System is defective.
- Wiring issue.
Try turning the Oven main power supply off for 1 minute. If the 420 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 421 mean on a GE Oven?
If your GE Oven is displaying an 421 fault code, it is indicating a Induction Coil Error has been detected by the internal self diagnostics system.
An 421 Induction Coil Error will set if the control board detects The induction coil is open.
The most common issues that will cause an 421 Induction Coil Error to display on a GE Oven are:
- The induction coil is defective.
- The Induction Power System is defective.
- Wiring issue.
Try turning the Oven main power supply off for 1 minute. If the 421 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 422 mean on a GE Oven?
If your GE Oven is displaying an 422 fault code, it is indicating a Induction Coil Error has been detected by the internal self diagnostics system.
An 422 Induction Coil Error will set if the control board detects The induction coil is open.
The most common issues that will cause an 422 Induction Coil Error to display on a GE Oven are:
- The induction coil is defective.
- The Induction Power System is defective.
- Wiring issue.
Try turning the Oven main power supply off for 1 minute. If the 422 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 423 mean on a GE Oven?
If your GE Oven is displaying an 423 fault code, it is indicating a Induction Coil Error has been detected by the internal self diagnostics system.
An 423 Induction Coil Error will set if the control board detects The induction coil is open.
The most common issues that will cause an 423 Induction Coil Error to display on a GE Oven are:
- The induction coil is defective.
- The Induction Power System is defective.
- Wiring issue.
Try turning the Oven main power supply off for 1 minute. If the 423 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 430 mean on a GE Oven?
If your GE Oven is displaying an 430 fault code, it is indicating a IGBT Sensor Error has been detected by the internal self diagnostics system.
An 430 IGBT Sensor Error will set if the control board detects The IGBT Sensor is shorted.
The most common issues that will cause an 430 IGBT Sensor Error to display on a GE Oven are:
- The IGBT sensor is defective.
- The inverter PCB is defective.
- Wiring issue between the top sensor and the inverter PCB.
Try turning the Oven main power supply off for 1 minute. If the 430 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 431 mean on a GE Oven?
If your GE Oven is displaying an 431 fault code, it is indicating a IGBT Sensor Error has been detected by the internal self diagnostics system.
An 431 IGBT Sensor Error will set if the control board detects The IGBT Sensor is shorted.
The most common issues that will cause an 431 IGBT Sensor Error to display on a GE Oven are:
- The IGBT sensor is defective.
- The inverter PCB is defective.
- Wiring issue between the top sensor and the inverter PCB.
Try turning the Oven main power supply off for 1 minute. If the 431 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 432 mean on a GE Oven?
If your GE Oven is displaying an 432 fault code, it is indicating a IGBT Sensor Error has been detected by the internal self diagnostics system.
An 432 IGBT Sensor Error will set if the control board detects The IGBT Sensor is shorted.
The most common issues that will cause an 432 IGBT Sensor Error to display on a GE Oven are:
- The IGBT sensor is defective.
- The inverter PCB is defective.
- Wiring issue between the top sensor and the inverter PCB.
Try turning the Oven main power supply off for 1 minute. If the 432 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 433 mean on a GE Oven?
If your GE Oven is displaying an 433 fault code, it is indicating a IGBT Sensor Error has been detected by the internal self diagnostics system.
An 433 IGBT Sensor Error will set if the control board detects The IGBT Sensor is shorted.
The most common issues that will cause an 433 IGBT Sensor Error to display on a GE Oven are:
- The IGBT sensor is defective.
- The inverter PCB is defective.
- Wiring issue between the top sensor and the inverter PCB.
Try turning the Oven main power supply off for 1 minute. If the 433 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 440 mean on a GE Oven?
If your GE Oven is displaying an 440 fault code, it is indicating a Voltage Error has been detected by the internal self diagnostics system.
An 440 Voltage Error will set if the control board detects The supply voltage is improperly wired.
The most common issues that will cause an 440 Voltage Error to display on a GE Oven are:
- The power supply is wired improperly.
- The cooktop or oven is wired improperly.
- The generator board is defective.
Try turning the Oven main power supply off for 1 minute. If the 440 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 441 mean on a GE Oven?
If your GE Oven is displaying an 441 fault code, it is indicating a Voltage Error has been detected by the internal self diagnostics system.
An 441 Voltage Error will set if the control board detects The supply voltage is improperly wired.
The most common issues that will cause an 441 Voltage Error to display on a GE Oven are:
- The power supply is wired improperly.
- The cooktop or oven is wired improperly.
- The generator board is defective.
Try turning the Oven main power supply off for 1 minute. If the 441 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 442 mean on a GE Oven?
If your GE Oven is displaying an 442 fault code, it is indicating a Voltage Error has been detected by the internal self diagnostics system.
An 442 Voltage Error will set if the control board detects The supply voltage is improperly wired.
The most common issues that will cause an 442 Voltage Error to display on a GE Oven are:
- The power supply is wired improperly.
- The cooktop or oven is wired improperly.
- The generator board is defective.
Try turning the Oven main power supply off for 1 minute. If the 442 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 443 mean on a GE Oven?
If your GE Oven is displaying an 443 fault code, it is indicating a Voltage Error has been detected by the internal self diagnostics system.
An 443 Voltage Error will set if the control board detects The supply voltage is improperly wired.
The most common issues that will cause an 443 Voltage Error to display on a GE Oven are:
- The power supply is wired improperly.
- The cooktop or oven is wired improperly.
- The generator board is defective.
Try turning the Oven main power supply off for 1 minute. If the 443 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 450 mean on a GE Oven?
If your GE Oven is displaying an 450 fault code, it is indicating a Voltage Error has been detected by the internal self diagnostics system.
An 450 Voltage Error will set if the control board detects The supply voltage is improperly wired.
The most common issues that will cause an 450 Voltage Error to display on a GE Oven are:
- The power supply is wired improperly.
- The cooktop or oven is wired improperly.
- The generator board is defective.
Try turning the Oven main power supply off for 1 minute. If the 450 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 451 mean on a GE Oven?
If your GE Oven is displaying an 451 fault code, it is indicating a Voltage Error has been detected by the internal self diagnostics system.
An 451 Voltage Error will set if the control board detects The supply voltage is improperly wired.
The most common issues that will cause an 451 Voltage Error to display on a GE Oven are:
- The power supply is wired improperly.
- The cooktop or oven is wired improperly.
- The generator board is defective.
Try turning the Oven main power supply off for 1 minute. If the 451 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 452 mean on a GE Oven?
If your GE Oven is displaying an 452 fault code, it is indicating a Voltage Error has been detected by the internal self diagnostics system.
An 452 Voltage Error will set if the control board detects The supply voltage is improperly wired.
The most common issues that will cause an 452 Voltage Error to display on a GE Oven are:
- The power supply is wired improperly.
- The cooktop or oven is wired improperly.
- The generator board is defective.
Try turning the Oven main power supply off for 1 minute. If the 452 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 453 mean on a GE Oven?
If your GE Oven is displaying an 453 fault code, it is indicating a Voltage Error has been detected by the internal self diagnostics system.
An 453 Voltage Error will set if the control board detects The supply voltage is improperly wired.
The most common issues that will cause an 453 Voltage Error to display on a GE Oven are:
- The power supply is wired improperly.
- The cooktop or oven is wired improperly.
- The generator board is defective.
Try turning the Oven main power supply off for 1 minute. If the 453 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 460 mean on a GE Oven?
If your GE Oven is displaying an 460 fault code, it is indicating a IGBT Temperature Error has been detected by the internal self diagnostics system.
An 460 IGBT Temperature Error will set if the control board detects Gen board 1, channel A IGBT temp> 115C
The most common issues that will cause an 460 IGBT Temperature Error to display on a GE Oven are:
- Restricted induction board cooling fan airflow.
- The induction board cooling fan is defective.
- The generator board is defective.
Try turning the Oven main power supply off for 1 minute. If the 460 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 461 mean on a GE Oven?
If your GE Oven is displaying an 461 fault code, it is indicating a IGBT Temperature Error has been detected by the internal self diagnostics system.
An 461 IGBT Temperature Error will set if the control board detects Gen board 2, channel A IGBT temp> 115C
The most common issues that will cause an 461 IGBT Temperature Error to display on a GE Oven are:
- Restricted induction board cooling fan airflow.
- The induction board cooling fan is defective.
- The generator board is defective.
Try turning the Oven main power supply off for 1 minute. If the 461 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 462 mean on a GE Oven?
If your GE Oven is displaying an 462 fault code, it is indicating a IGBT Temperature Error has been detected by the internal self diagnostics system.
An 462 IGBT Temperature Error will set if the control board detects Gen board 1, channel B IGBT temp> 115C
The most common issues that will cause an 462 IGBT Temperature Error to display on a GE Oven are:
- Restricted induction board cooling fan airflow.
- The induction board cooling fan is defective.
- The generator board is defective.
Try turning the Oven main power supply off for 1 minute. If the 462 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 463 mean on a GE Oven?
If your GE Oven is displaying an 463 fault code, it is indicating a IGBT Temperature Error has been detected by the internal self diagnostics system.
An 463 IGBT Temperature Error will set if the control board detects Gen board 2, channel B IGBT temp> 115C
The most common issues that will cause an 463 IGBT Temperature Error to display on a GE Oven are:
- Restricted induction board cooling fan airflow.
- The induction board cooling fan is defective.
- The generator board is defective.
Try turning the Oven main power supply off for 1 minute. If the 463 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 470 mean on a GE Oven?
If your GE Oven is displaying an 470 fault code, it is indicating a Configuration Error has been detected by the internal self diagnostics system.
An 470 Configuration Error will set if the control board detects Gen board 1, channel A configuration missing
The most common issues that will cause an 470 Configuration Error to display on a GE Oven are:
- Check LPID jumpers on gen board, J501 & J502
- The generator board is defective.
- The machine control board is defective.
Try turning the Oven main power supply off for 1 minute. If the 470 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 471 mean on a GE Oven?
If your GE Oven is displaying an 471 fault code, it is indicating a Configuration Error has been detected by the internal self diagnostics system.
An 471 Configuration Error will set if the control board detects Gen board 2, channel A configuration missing
The most common issues that will cause an 471 Configuration Error to display on a GE Oven are:
- Check LPID jumpers on gen board, J501 & J502
- The generator board is defective.
- The machine control board is defective.
Try turning the Oven main power supply off for 1 minute. If the 471 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 480 mean on a GE Oven?
If your GE Oven is displaying an 480 fault code, it is indicating a Configuration Error has been detected by the internal self diagnostics system.
An 480 Configuration Error will set if the control board detects Gen board 1, channel B configuration missing
The most common issues that will cause an 480 Configuration Error to display on a GE Oven are:
- Check LPID jumpers on gen board, J501 & J502
- The generator board is defective.
- The machine control board is defective.
Try turning the Oven main power supply off for 1 minute. If the 480 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 481 mean on a GE Oven?
If your GE Oven is displaying an 481 fault code, it is indicating a Configuration Error has been detected by the internal self diagnostics system.
An 481 Configuration Error will set if the control board detects Gen board 2, channel B configuration missing
The most common issues that will cause an 481 Configuration Error to display on a GE Oven are:
- Check LPID jumpers on gen board, J501 & J502
- The generator board is defective.
- The machine control board is defective.
Try turning the Oven main power supply off for 1 minute. If the 481 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 490 mean on a GE Oven?
If your GE Oven is displaying an 490 fault code, it is indicating a Communication Error has been detected by the internal self diagnostics system.
An 490 Communication Error will set if the control board detects Gen board 1, channel A comm loss
The most common issues that will cause an 490 Communication Error to display on a GE Oven are:
- Wiring or power supply issue.
- The generator board is defective.
- The machine control board is defective.
Try turning the Oven main power supply off for 1 minute. If the 490 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 491 mean on a GE Oven?
If your GE Oven is displaying an 491 fault code, it is indicating a Communication Error has been detected by the internal self diagnostics system.
An 491 Communication Error will set if the control board detects Gen board 2, channel A comm loss
The most common issues that will cause an 491 Communication Error to display on a GE Oven are:
- Wiring or power supply issue.
- The generator board is defective.
- The machine control board is defective.
Try turning the Oven main power supply off for 1 minute. If the 491 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 500 mean on a GE Oven?
If your GE Oven is displaying an 500 fault code, it is indicating a Communication Error has been detected by the internal self diagnostics system.
An 500 Communication Error will set if the control board detects Gen board 1, channel B comm loss
The most common issues that will cause an 500 Communication Error to display on a GE Oven are:
- Wiring or power supply issue.
- The generator board is defective.
- The machine control board is defective.
Try turning the Oven main power supply off for 1 minute. If the 500 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 501 mean on a GE Oven?
If your GE Oven is displaying an 501 fault code, it is indicating a Communication Error has been detected by the internal self diagnostics system.
An 501 Communication Error will set if the control board detects Gen board 2, channel B comm loss
The most common issues that will cause an 501 Communication Error to display on a GE Oven are:
- Wiring or power supply issue.
- The generator board is defective.
- The machine control board is defective.
Try turning the Oven main power supply off for 1 minute. If the 501 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 630 mean on a GE Oven?
If your GE Oven is displaying an 630 fault code, it is indicating a Communication Error has been detected by the internal self diagnostics system.
An 630 Communication Error will set if the control board detects Gen board 1 communication missing to the oven machine control
The most common issues that will cause an 630 Communication Error to display on a GE Oven are:
- Wiring or power supply issue.
- The generator board is defective.
- The machine control board is defective.
Try turning the Oven main power supply off for 1 minute. If the 630 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 640 mean on a GE Oven?
If your GE Oven is displaying an 640 fault code, it is indicating a Communication Error has been detected by the internal self diagnostics system.
An 640 Communication Error will set if the control board detects Gen board 2 communication missing to the oven machine control
The most common issues that will cause an 640 Communication Error to display on a GE Oven are:
- Wiring or power supply issue.
- The generator board is defective.
- The machine control board is defective.
Try turning the Oven main power supply off for 1 minute. If the 640 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 682 mean on a GE Oven?
If your GE Oven is displaying an 682 fault code, it is indicating a Communication Error has been detected by the internal self diagnostics system.
An 682 Communication Error will set if the control board detects Left Cooktop Ul communication missing to the oven machine control
The most common issues that will cause an 682 Communication Error to display on a GE Oven are:
- Wiring or power supply issue.
- The UI control is defective.
- The machine control board is defective.
Try turning the Oven main power supply off for 1 minute. If the 682 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 683 mean on a GE Oven?
If your GE Oven is displaying an 683 fault code, it is indicating a Communication Error has been detected by the internal self diagnostics system.
An 683 Communication Error will set if the control board detects Oven Ul communication missing to the oven machine control
The most common issues that will cause an 683 Communication Error to display on a GE Oven are:
- Wiring or power supply issue.
- The UI control is defective.
- The machine control board is defective.
Try turning the Oven main power supply off for 1 minute. If the 683 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does 684 mean on a GE Oven?
If your GE Oven is displaying an 684 fault code, it is indicating a Communication Error has been detected by the internal self diagnostics system.
An 684 Communication Error will set if the control board detects Right Cooktop Ul communication missing to the oven machine control
The most common issues that will cause an 684 Communication Error to display on a GE Oven are:
- Wiring or power supply issue.
- The UI control is defective.
- The machine control board is defective.
Try turning the Oven main power supply off for 1 minute. If the 684 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does ⊃ mean on a GE Oven?
If your GE Oven is displaying an ⊃ fault code, it is indicating a Sabbath Mode has been detected by the internal self diagnostics system.
An ⊃ Sabbath Mode will set if the control board detects The oven is in Sabbath Mode.
The most common issues that will cause an ⊃ Sabbath Mode to display on a GE Oven are:
- When a ⊃ (backwards “C”) is seen in the display, it means that your oven has been set for Sabbath Mode. See the user manual for Sabbath Mode instructions.
Try turning the Oven main power supply off for 1 minute. If the ⊃ code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does Bad Line mean on a GE Oven?
If your GE Oven is displaying an Bad Line fault code, it is indicating a Control Panel Error has been detected by the internal self diagnostics system.
An Bad Line Control Panel Error will set if the control board detects The oven is not wired correctly.
The most common issues that will cause an Bad Line Control Panel Error to display on a GE Oven are:
- The oven outlet is not wired correctly.
- The oven control PCB is defective.
- The oven power cable is not wired correctly.
Try turning the Oven main power supply off for 1 minute. If the Bad Line code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does ERR mean on a GE Oven?
If your GE Oven is displaying an ERR fault code, it is indicating a Invalid Entry has been detected by the internal self diagnostics system.
An ERR Invalid Entry will set if the control board detects ERR means that there has been an invalid entry when setting the oven controls.
The most common issues that will cause an ERR Invalid Entry to display on a GE Oven are:
- Check the oven user manual.
Try turning the Oven main power supply off for 1 minute. If the ERR code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F0 mean on a GE Oven?
If your GE Oven is displaying an F0 fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F0 Key Panel Error will set if the control board detects Any button is stuck or held for more than 30 seconds.
The most common issues that will cause an F0 Key Panel Error to display on a GE Oven are:
- The keypad is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F0 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F1 mean on a GE Oven?
If your GE Oven is displaying an F1 fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F1 Key Panel Error will set if the control board detects Any button is stuck or held for more than 30 seconds.
The most common issues that will cause an F1 Key Panel Error to display on a GE Oven are:
- The keypad is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F1 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F2 mean on a GE Oven?
If your GE Oven is displaying an F2 fault code, it is indicating a Over Temperature Error has been detected by the internal self diagnostics system.
An F2 Over Temperature Error will set if the control board detects The oven has exceeded the max temperature.
The most common issues that will cause an F2 Over Temperature Error to display on a GE Oven are:
- The oven control board is defective.
Try turning the Oven main power supply off for 1 minute. If the F2 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F3 mean on a GE Oven?
If your GE Oven is displaying an F3 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.
An F3 Temperature Sensor Error will set if the control board detects The oven temperature sensor is open or shorted.
The most common issues that will cause an F3 Temperature Sensor Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F3 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F4 mean on a GE Oven?
If your GE Oven is displaying an F4 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.
An F4 Temperature Sensor Error will set if the control board detects The oven temperature sensor is open or shorted.
The most common issues that will cause an F4 Temperature Sensor Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F4 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F5 mean on a GE Oven?
If your GE Oven is displaying an F5 fault code, it is indicating a Control Panel Error has been detected by the internal self diagnostics system.
An F5 Control Panel Error will set if the control board detects There is an internal oven control panel issue.
The most common issues that will cause an F5 Control Panel Error to display on a GE Oven are:
- The oven control board is defective.
Try turning the Oven main power supply off for 1 minute. If the F5 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F6 mean on a GE Oven?
If your GE Oven is displaying an F6 fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F6 Key Panel Error will set if the control board detects Any button is stuck or held for more than 30 seconds.
The most common issues that will cause an F6 Key Panel Error to display on a GE Oven are:
- The keypad is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F6 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F7 mean on a GE Oven?
If your GE Oven is displaying an F7 fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F7 Key Panel Error will set if the control board detects Any button is stuck or held for more than 30 seconds.
The most common issues that will cause an F7 Key Panel Error to display on a GE Oven are:
- The keypad is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F7 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F8 mean on a GE Oven?
If your GE Oven is displaying an F8 fault code, it is indicating a EEPROM Error has been detected by the internal self diagnostics system.
An F8 EEPROM Error will set if the control board detects There is an internal oven control panel issue.
The most common issues that will cause an F8 EEPROM Error to display on a GE Oven are:
- The oven control board is defective.
Try turning the Oven main power supply off for 1 minute. If the F8 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F9 mean on a GE Oven?
If your GE Oven is displaying an F9 fault code, it is indicating a Door Latch Error has been detected by the internal self diagnostics system.
An F9 Door Latch Error will set if the control board detects The oven door lock is not functioning when initiated.
The most common issues that will cause an F9 Door Latch Error to display on a GE Oven are:
- The door lock switch is defective.
- The door lock motor is defective.
- The oven control PCB is defective.
- Wiring issue between the door lock switch and the control PCB.
- Wiring issue between the door lock motor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F9 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F20 mean on a GE Oven?
If your GE Oven is displaying an F20 fault code, it is indicating a Over Temperature Error has been detected by the internal self diagnostics system.
An F20 Over Temperature Error will set if the control board detects The upper oven temperature has exceeded max unlock temperature with the oven door unlocked.
The most common issues that will cause an F20 Over Temperature Error to display on a GE Oven are:
- The oven control board is defective.
Try turning the Oven main power supply off for 1 minute. If the F20 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F21 mean on a GE Oven?
If your GE Oven is displaying an F21 fault code, it is indicating a Over Temperature Error has been detected by the internal self diagnostics system.
An F21 Over Temperature Error will set if the control board detects The upper oven temperature has exceeded max lock temperature with the oven door locked.
The most common issues that will cause an F21 Over Temperature Error to display on a GE Oven are:
- The oven control board is defective.
Try turning the Oven main power supply off for 1 minute. If the F21 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F22 mean on a GE Oven?
If your GE Oven is displaying an F22 fault code, it is indicating a Over Temperature Error has been detected by the internal self diagnostics system.
An F22 Over Temperature Error will set if the control board detects The lower oven temperature has exceeded max unlock temperature with the oven door unlocked.
The most common issues that will cause an F22 Over Temperature Error to display on a GE Oven are:
- The oven control board is defective.
Try turning the Oven main power supply off for 1 minute. If the F22 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F23 mean on a GE Oven?
If your GE Oven is displaying an F23 fault code, it is indicating a Over Temperature Error has been detected by the internal self diagnostics system.
An F23 Over Temperature Error will set if the control board detects The lower oven temperature has exceeded max lock temperature with the oven door locked.
The most common issues that will cause an F23 Over Temperature Error to display on a GE Oven are:
- The oven control board is defective.
Try turning the Oven main power supply off for 1 minute. If the F23 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F30 mean on a GE Oven?
If your GE Oven is displaying an F30 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.
An F30 Temperature Sensor Error will set if the control board detects The upper oven temperature sensor is shorted.
The most common issues that will cause an F30 Temperature Sensor Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F30 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F31 mean on a GE Oven?
If your GE Oven is displaying an F31 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.
An F31 Temperature Sensor Error will set if the control board detects The upper oven temperature sensor is open.
The most common issues that will cause an F31 Temperature Sensor Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F31 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F32 mean on a GE Oven?
If your GE Oven is displaying an F32 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.
An F32 Temperature Sensor Error will set if the control board detects The lower oven temperature sensor is shorted.
The most common issues that will cause an F32 Temperature Sensor Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F32 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F33 mean on a GE Oven?
If your GE Oven is displaying an F33 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.
An F33 Temperature Sensor Error will set if the control board detects The lower oven temperature sensor is open.
The most common issues that will cause an F33 Temperature Sensor Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F33 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F34 mean on a GE Oven?
If your GE Oven is displaying an F34 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.
An F34 Temperature Sensor Error will set if the control board detects CRC calibration has failed or fine tune temperature difference of more than 50 deg Fahrenheit
The most common issues that will cause an F34 Temperature Sensor Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F34 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F35 mean on a GE Oven?
If your GE Oven is displaying an F35 fault code, it is indicating a Temperature Sensor Error has been detected by the internal self diagnostics system.
An F35 Temperature Sensor Error will set if the control board detects CRC calibration has failed or fine tune temperature difference of more than 50 deg Fahrenheit
The most common issues that will cause an F35 Temperature Sensor Error to display on a GE Oven are:
- The oven temperature sensor is defective.
- The oven control PCB is defective.
- Wiring issue between the oven temperature sensor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F35 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F70 mean on a GE Oven?
If your GE Oven is displaying an F70 fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F70 Key Panel Error will set if the control board detects The clear or off button is stuck or held for more than 30 seconds.
The most common issues that will cause an F70 Key Panel Error to display on a GE Oven are:
- The keypad is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F70 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F71 mean on a GE Oven?
If your GE Oven is displaying an F71 fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F71 Key Panel Error will set if the control board detects Any button is stuck or held for more than 30 seconds.
The most common issues that will cause an F71 Key Panel Error to display on a GE Oven are:
- The keypad is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F71 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F72 mean on a GE Oven?
If your GE Oven is displaying an F72 fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F72 Key Panel Error will set if the control board detects Any glass touch button is stuck or held for more than 30 seconds.
The most common issues that will cause an F72 Key Panel Error to display on a GE Oven are:
- The glass touch panel is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F72 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F73 mean on a GE Oven?
If your GE Oven is displaying an F73 fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F73 Key Panel Error will set if the control board detects Any glass touch button is stuck or held for more than 30 seconds.
The most common issues that will cause an F73 Key Panel Error to display on a GE Oven are:
- The glass touch panel is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F73 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F74 mean on a GE Oven?
If your GE Oven is displaying an F74 fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F74 Key Panel Error will set if the control board detects Any glass touch button is stuck or held for more than 30 seconds.
The most common issues that will cause an F74 Key Panel Error to display on a GE Oven are:
- The glass touch panel is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F74 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F75 mean on a GE Oven?
If your GE Oven is displaying an F75 fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F75 Key Panel Error will set if the control board detects Any glass touch button is stuck or held for more than 30 seconds.
The most common issues that will cause an F75 Key Panel Error to display on a GE Oven are:
- The glass touch panel is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F75 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F76 mean on a GE Oven?
If your GE Oven is displaying an F76 fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F76 Key Panel Error will set if the control board detects Any glass touch button is stuck or held for more than 30 seconds.
The most common issues that will cause an F76 Key Panel Error to display on a GE Oven are:
- The glass touch panel is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F76 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F77 mean on a GE Oven?
If your GE Oven is displaying an F77 fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F77 Key Panel Error will set if the control board detects Any glass touch button is stuck or held for more than 30 seconds.
The most common issues that will cause an F77 Key Panel Error to display on a GE Oven are:
- The glass touch panel is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F77 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F78 mean on a GE Oven?
If your GE Oven is displaying an F78 fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F78 Key Panel Error will set if the control board detects Any glass touch button is stuck or held for more than 30 seconds.
The most common issues that will cause an F78 Key Panel Error to display on a GE Oven are:
- The glass touch panel is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F78 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F79 mean on a GE Oven?
If your GE Oven is displaying an F79 fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F79 Key Panel Error will set if the control board detects Any glass touch button is stuck or held for more than 30 seconds.
The most common issues that will cause an F79 Key Panel Error to display on a GE Oven are:
- The glass touch panel is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F79 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F7A mean on a GE Oven?
If your GE Oven is displaying an F7A fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F7A Key Panel Error will set if the control board detects Any button other than start or clear is stuck or held for more than 30 seconds.
The most common issues that will cause an F7A Key Panel Error to display on a GE Oven are:
- The keypad is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F7A code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F7B mean on a GE Oven?
If your GE Oven is displaying an F7B fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F7B Key Panel Error will set if the control board detects The start button is stuck or held for more than 30 seconds.
The most common issues that will cause an F7B Key Panel Error to display on a GE Oven are:
- The keypad is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F7B code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F7C mean on a GE Oven?
If your GE Oven is displaying an F7C fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F7C Key Panel Error will set if the control board detects The upper clear button is stuck or held for more than 30 seconds.
The most common issues that will cause an F7C Key Panel Error to display on a GE Oven are:
- The keypad is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F7C code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F7D mean on a GE Oven?
If your GE Oven is displaying an F7D fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F7D Key Panel Error will set if the control board detects The lower clear button is stuck or held for more than 30 seconds.
The most common issues that will cause an F7D Key Panel Error to display on a GE Oven are:
- The keypad is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F7D code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F7E mean on a GE Oven?
If your GE Oven is displaying an F7E fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F7E Key Panel Error will set if the control board detects There has been a glass touch communication failure.
The most common issues that will cause an F7E Key Panel Error to display on a GE Oven are:
- The glass touch board is defective.
- The oven display board is defective.
- Wiring issue between the lass touch board and the oven display board.
Try turning the Oven main power supply off for 1 minute. If the F7E code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F7F mean on a GE Oven?
If your GE Oven is displaying an F7F fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F7F Key Panel Error will set if the control board detects There has been a glass touch communication failure.
The most common issues that will cause an F7F Key Panel Error to display on a GE Oven are:
- The glass touch board is defective.
- The oven display board is defective.
- Wiring issue between the lass touch board and the oven display board.
Try turning the Oven main power supply off for 1 minute. If the F7F code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F7X mean on a GE Oven?
If your GE Oven is displaying an F7X fault code, it is indicating a Key Panel Error has been detected by the internal self diagnostics system.
An F7X Key Panel Error will set if the control board detects Any button is stuck or held for more than 30 seconds.
The most common issues that will cause an F7X Key Panel Error to display on a GE Oven are:
- The keypad is defective.
- The oven control PCB is defective.
- Wiring issue between the keypad and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F7X code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F82 mean on a GE Oven?
If your GE Oven is displaying an F82 fault code, it is indicating a EEPROM Error has been detected by the internal self diagnostics system.
An F82 EEPROM Error will set if the control board detects There is an internal oven control panel issue.
The most common issues that will cause an F82 EEPROM Error to display on a GE Oven are:
- The oven control board is defective.
Try turning the Oven main power supply off for 1 minute. If the F82 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F90 mean on a GE Oven?
If your GE Oven is displaying an F90 fault code, it is indicating a Door Latch Error has been detected by the internal self diagnostics system.
An F90 Door Latch Error will set if the control board detects The upper oven door lock is not functioning when initiated.
The most common issues that will cause an F90 Door Latch Error to display on a GE Oven are:
- The door lock switch is defective.
- The door lock motor is defective.
- The oven control PCB is defective.
- Wiring issue between the door lock switch and the control PCB.
- Wiring issue between the door lock motor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F90 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F91 mean on a GE Oven?
If your GE Oven is displaying an F91 fault code, it is indicating a Door Latch Error has been detected by the internal self diagnostics system.
An F91 Door Latch Error will set if the control board detects The upper oven door lock is not functioning when initiated.
The most common issues that will cause an F91 Door Latch Error to display on a GE Oven are:
- The door lock switch is defective.
- The door lock motor is defective.
- The oven control PCB is defective.
- Wiring issue between the door lock switch and the control PCB.
- Wiring issue between the door lock motor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F91 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F92 mean on a GE Oven?
If your GE Oven is displaying an F92 fault code, it is indicating a Door Latch Error has been detected by the internal self diagnostics system.
An F92 Door Latch Error will set if the control board detects The upper oven door lock is not functioning when initiated.
The most common issues that will cause an F92 Door Latch Error to display on a GE Oven are:
- The door lock switch is defective.
- The door lock motor is defective.
- The oven control PCB is defective.
- Wiring issue between the door lock switch and the control PCB.
- Wiring issue between the door lock motor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F92 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F93 mean on a GE Oven?
If your GE Oven is displaying an F93 fault code, it is indicating a Door Latch Error has been detected by the internal self diagnostics system.
An F93 Door Latch Error will set if the control board detects The lower oven door lock is not functioning when initiated.
The most common issues that will cause an F93 Door Latch Error to display on a GE Oven are:
- The door lock switch is defective.
- The door lock motor is defective.
- The oven control PCB is defective.
- Wiring issue between the door lock switch and the control PCB.
- Wiring issue between the door lock motor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F93 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F94 mean on a GE Oven?
If your GE Oven is displaying an F94 fault code, it is indicating a Door Latch Error has been detected by the internal self diagnostics system.
An F94 Door Latch Error will set if the control board detects The lower oven door lock is not functioning when initiated.
The most common issues that will cause an F94 Door Latch Error to display on a GE Oven are:
- The door lock switch is defective.
- The door lock motor is defective.
- The oven control PCB is defective.
- Wiring issue between the door lock switch and the control PCB.
- Wiring issue between the door lock motor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F94 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F95 mean on a GE Oven?
If your GE Oven is displaying an F95 fault code, it is indicating a Door Latch Error has been detected by the internal self diagnostics system.
An F95 Door Latch Error will set if the control board detects The lower oven door lock is not functioning when initiated.
The most common issues that will cause an F95 Door Latch Error to display on a GE Oven are:
- The door lock switch is defective.
- The door lock motor is defective.
- The oven control PCB is defective.
- Wiring issue between the door lock switch and the control PCB.
- Wiring issue between the door lock motor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F95 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F96 mean on a GE Oven?
If your GE Oven is displaying an F96 fault code, it is indicating a Cooling Fan Error has been detected by the internal self diagnostics system.
An F96 Cooling Fan Error will set if the control board detects The cooling fan is not functioning or spinning slowly.
The most common issues that will cause an F96 Cooling Fan Error to display on a GE Oven are:
- The cooling fan motor is defective.
- The cooling fan blade is defective.
- The oven control PCB is defective.
- Wiring issue between the cooling fan and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F96 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F97 mean on a GE Oven?
If your GE Oven is displaying an F97 fault code, it is indicating a Cooling Fan Error has been detected by the internal self diagnostics system.
An F97 Cooling Fan Error will set if the control board detects The cooling fan is not functioning or spinning slowly.
The most common issues that will cause an F97 Cooling Fan Error to display on a GE Oven are:
- The cooling fan motor is defective.
- The cooling fan blade is defective.
- The oven control PCB is defective.
- Wiring issue between the cooling fan and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F97 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F98 mean on a GE Oven?
If your GE Oven is displaying an F98 fault code, it is indicating a Cooling Fan Error has been detected by the internal self diagnostics system.
An F98 Cooling Fan Error will set if the control board detects The cooling fan is not functioning or spinning too fast.
The most common issues that will cause an F98 Cooling Fan Error to display on a GE Oven are:
- The cooling fan motor is defective.
- The cooling fan blade is defective.
- The oven control PCB is defective.
- Wiring issue between the cooling fan and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F98 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does F99 mean on a GE Oven?
If your GE Oven is displaying an F99 fault code, it is indicating a Cooling Fan Error has been detected by the internal self diagnostics system.
An F99 Cooling Fan Error will set if the control board detects The cooling fan is not functioning or spinning too fast.
The most common issues that will cause an F99 Cooling Fan Error to display on a GE Oven are:
- The cooling fan motor is defective.
- The cooling fan blade is defective.
- The oven control PCB is defective.
- Wiring issue between the cooling fan and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the F99 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does FC mean on a GE Oven?
If your GE Oven is displaying an FC fault code, it is indicating a Door Latch Error has been detected by the internal self diagnostics system.
An FC Door Latch Error will set if the control board detects The oven door lock is not functioning when initiated.
The most common issues that will cause an FC Door Latch Error to display on a GE Oven are:
- The door lock switch is defective.
- The door lock motor is defective.
- The oven control PCB is defective.
- Wiring issue between the door lock switch and the control PCB.
- Wiring issue between the door lock motor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the FC code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does FD mean on a GE Oven?
If your GE Oven is displaying an FD fault code, it is indicating a Probe Error has been detected by the internal self diagnostics system.
An FD Probe Error will set if the control board detects The meat probe is open or shorted.
The most common issues that will cause an FD Probe Error to display on a GE Oven are:
- The meat probe is defective.
- The oven control PCB is defective.
- Wiring issue between the meat probe and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the FD code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does FF mean on a GE Oven?
If your GE Oven is displaying an FF fault code, it is indicating a Control Panel Error has been detected by the internal self diagnostics system.
An FF Control Panel Error will set if the control board detects There is an internal oven control panel issue.
The most common issues that will cause an FF Control Panel Error to display on a GE Oven are:
- The oven control board is defective.
Try turning the Oven main power supply off for 1 minute. If the FF code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does LOC mean on a GE Oven?
If your GE Oven is displaying an LOC fault code, it is indicating a Child Lock has been detected by the internal self diagnostics system.
An LOC Child Lock will set if the control board detects The child lock has been activated.
The most common issues that will cause an LOC Child Lock to display on a GE Oven are:
- Check the oven user manual.
Try turning the Oven main power supply off for 1 minute. If the LOC code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
What does Unlock Door mean on a GE Oven?
If your GE Oven is displaying an Unlock Door fault code, it is indicating a Door Latch Error has been detected by the internal self diagnostics system.
An Unlock Door Door Latch Error will set if the control board detects The oven door lock is not functioning when initiated.
The most common issues that will cause an Unlock Door Door Latch Error to display on a GE Oven are:
- The door lock switch is defective.
- The door lock motor is defective.
- The oven control PCB is defective.
- Wiring issue between the door lock switch and the control PCB.
- Wiring issue between the door lock motor and the control PCB.
Try turning the Oven main power supply off for 1 minute. If the Unlock Door code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error
GE Oven Error Codes Disclaimer
The GE Oven Error Codes information contained on this page is provided for informational purposes only. ApplianceFaultCodes.com does not guarantee the information to be correct or give a proper diagnosis of any appliance. Always take proper safety precautions when installing or repairing any major appliance.