GE Fridge Error Codes - Appliance Fault Codes

The first thing to try is switching the Fridge main power supply off for 60 seconds. This usual only works if the fault was set due to a supply voltage fluctuation from a storm or power outage. It may also work if the problem is intermittent. Unfortunately this might only be a short term solution because if the problem is intermittent and the fault returns, the error code will display again.

If that doesn’t work, the problem triggering the error code will need to be repaired in order to clear the fault code.

Why is my GE Fridge not working?

Some GE Fridge error codes will disable the appliance from operating. The error code will need to be resolved in order for the appliance to function normally again.

What does 88 mean on a GE Fridge?

If your GE Fridge is displaying an 88 fault code, it is indicating a Control Board Error has been detected by the internal self diagnostics system.

An 88 Control Board Error will set if the control board detects Unplug the refrigerator for 5 minutes and then plugging it back in. The control board may have experienced a power surge.

The most common issues that will cause an 88 Control Board Error to display on a GE Fridge are:

Faulty main control board.
Electrical power surge.

Try turning the Fridge main power supply off for 1 minute. If the 88 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does 89 mean on a GE Fridge?

If your GE Fridge is displaying an 89 fault code, it is indicating a Control Board Error has been detected by the internal self diagnostics system.

An 89 Control Board Error will set if the control board detects Unplug the refrigerator for 5 minutes and then plugging it back in. The control board may have experienced a power surge.

The most common issues that will cause an 89 Control Board Error to display on a GE Fridge are:

Faulty main control board.
Electrical power surge.

Try turning the Fridge main power supply off for 1 minute. If the 89 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does CC mean on a GE Fridge?

If your GE Fridge is displaying an CC fault code, it is indicating a Temperature Error has been detected by the internal self diagnostics system.

An CC Temperature Error will set if the control board detects The freezer or fridge temperature is too warm.

The most common issues that will cause an CC Temperature Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the CC code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does CI mean on a GE Fridge?

If your GE Fridge is displaying an CI fault code, it is indicating a Ice Maker Error has been detected by the internal self diagnostics system.

An CI Ice Maker Error will set if the control board detects Check the ice maker for proper operation.

The most common issues that will cause an CI Ice Maker Error to display on a GE Fridge are:

Faulty ice maker.
Faulty wiring to ice maker.

Try turning the Fridge main power supply off for 1 minute. If the CI code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does dE mean on a GE Fridge?

If your GE Fridge is displaying an dE fault code, it is indicating a Defrost Error has been detected by the internal self diagnostics system.

An dE Defrost Error will set if the control board detects The freezer defrost loop is open or the defrost operation has taken longer than expected.

The most common issues that will cause an dE Defrost Error to display on a GE Fridge are:

The defrost heater is defective.
The defrost temperature sensor is defective.
The defrost high limit sensor is defective.
The main PCB is defective.
Wiring issue between the defrost loop and the main PCB.
The defrost room is overwhelmed with ice.

Try turning the Fridge main power supply off for 1 minute. If the dE code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does DF mean on a GE Fridge?

If your GE Fridge is displaying an DF fault code, it is indicating a Defrost Error has been detected by the internal self diagnostics system.

An DF Defrost Error will set if the control board detects The freezer defrost loop is open or the defrost operation has taken longer than expected.

The most common issues that will cause an DF Defrost Error to display on a GE Fridge are:

The defrost heater is defective.
The defrost temperature sensor is defective.
The defrost high limit sensor is defective.
The main PCB is defective.
Wiring issue between the defrost loop and the main PCB.
The defrost room is overwhelmed with ice.

Try turning the Fridge main power supply off for 1 minute. If the DF code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does E2 mean on a GE Fridge?

If your GE Fridge is displaying an E2 fault code, it is indicating a Control Board Error has been detected by the internal self diagnostics system.

An E2 Control Board Error will set if the control board detects Unplug the refrigerator for 5 minutes and then plugging it back in. The control board may have experienced a power surge.

The most common issues that will cause an E2 Control Board Error to display on a GE Fridge are:

Faulty main control board.
Electrical power surge.

Try turning the Fridge main power supply off for 1 minute. If the E2 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does EC mean on a GE Fridge?

If your GE Fridge is displaying an EC fault code, it is indicating a Turbo Cool has been detected by the internal self diagnostics system.

An EC Turbo Cool will set if the control board detects This is not an error.

The most common issues that will cause an EC Turbo Cool to display on a GE Fridge are:

The Turbo Cool Function is turned on

Try turning the Fridge main power supply off for 1 minute. If the EC code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does EF mean on a GE Fridge?

If your GE Fridge is displaying an EF fault code, it is indicating a Turbo Freeze has been detected by the internal self diagnostics system.

An EF Turbo Freeze will set if the control board detects This is not an error.

The most common issues that will cause an EF Turbo Freeze to display on a GE Fridge are:

The Turbo Freeze Function is turned on

Try turning the Fridge main power supply off for 1 minute. If the EF code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F1 mean on a GE Fridge?

If your GE Fridge is displaying an F1 fault code, it is indicating a Thermistor Error has been detected by the internal self diagnostics system.

An F1 Thermistor Error will set if the control board detects The refrigerator cabinet thermistor (temperature sensor) signal is invalid.

The most common issues that will cause an F1 Thermistor Error to display on a GE Fridge are:

The thermistor (temperature sensor) is defective.
The main PCB is defective.
Wiring issue between the thermistor (temperature sensor) and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F1 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F10 mean on a GE Fridge?

If your GE Fridge is displaying an F10 fault code, it is indicating a Thermistor Error has been detected by the internal self diagnostics system.

An F10 Thermistor Error will set if the control board detects The freezer cabinet ice maker mold thermistor (temperature sensor) signal is invalid.

The most common issues that will cause an F10 Thermistor Error to display on a GE Fridge are:

The thermistor (temperature sensor) is defective.
The main PCB is defective.
Wiring issue between the thermistor (temperature sensor) and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F10 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F100 mean on a GE Fridge?

If your GE Fridge is displaying an F100 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F100 Fan Motor Error will set if the control board detects The freezer fan feedback signal is missing when fan is running.

The most common issues that will cause an F100 Fan Motor Error to display on a GE Fridge are:

The fan motor is defective.
The fan blade is jammed.
The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F100 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F101 mean on a GE Fridge?

If your GE Fridge is displaying an F101 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F101 Fan Motor Error will set if the control board detects The freezer fan feedback signal is present when the fan is off.

The most common issues that will cause an F101 Fan Motor Error to display on a GE Fridge are:

The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F101 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F102 mean on a GE Fridge?

If your GE Fridge is displaying an F102 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F102 Fan Motor Error will set if the control board detects The freezer fan cannot reach the target RPM.

The most common issues that will cause an F102 Fan Motor Error to display on a GE Fridge are:

The fan motor is defective.
The fan blade is jammed.
The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F102 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F103 mean on a GE Fridge?

If your GE Fridge is displaying an F103 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F103 Fan Motor Error will set if the control board detects The condenser can feedback signal is missing when fan is running.

The most common issues that will cause an F103 Fan Motor Error to display on a GE Fridge are:

The fan motor is defective.
The fan blade is jammed.
The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F103 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F104 mean on a GE Fridge?

If your GE Fridge is displaying an F104 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F104 Fan Motor Error will set if the control board detects The condenser fan feedback signal is present when the fan is off.

The most common issues that will cause an F104 Fan Motor Error to display on a GE Fridge are:

The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F104 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F105 mean on a GE Fridge?

If your GE Fridge is displaying an F105 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F105 Fan Motor Error will set if the control board detects The condenser fan cannot reach the target RPM.

The most common issues that will cause an F105 Fan Motor Error to display on a GE Fridge are:

The fan motor is defective.
The fan blade is jammed.
The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F105 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F106 mean on a GE Fridge?

If your GE Fridge is displaying an F106 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F106 Fan Motor Error will set if the control board detects The refrigerator fan feedback signal is missing when fan is running.

The most common issues that will cause an F106 Fan Motor Error to display on a GE Fridge are:

The fan motor is defective.
The fan blade is jammed.
The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F106 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F107 mean on a GE Fridge?

If your GE Fridge is displaying an F107 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F107 Fan Motor Error will set if the control board detects The refrigerator fan feedback signal is present when the fan is off.

The most common issues that will cause an F107 Fan Motor Error to display on a GE Fridge are:

The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F107 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F108 mean on a GE Fridge?

If your GE Fridge is displaying an F108 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F108 Fan Motor Error will set if the control board detects The refrigerator fan cannot reach the target RPM.

The most common issues that will cause an F108 Fan Motor Error to display on a GE Fridge are:

The fan motor is defective.
The fan blade is jammed.
The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F108 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F109 mean on a GE Fridge?

If your GE Fridge is displaying an F109 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F109 Fan Motor Error will set if the control board detects The ice box fan feedback signal is missing when fan is running.

The most common issues that will cause an F109 Fan Motor Error to display on a GE Fridge are:

The fan motor is defective.
The fan blade is jammed.
The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F109 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F110 mean on a GE Fridge?

If your GE Fridge is displaying an F110 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F110 Fan Motor Error will set if the control board detects The ice box fan feedback signal is present when the fan is off.

The most common issues that will cause an F110 Fan Motor Error to display on a GE Fridge are:

The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F110 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F111 mean on a GE Fridge?

If your GE Fridge is displaying an F111 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F111 Fan Motor Error will set if the control board detects The ice box fan cannot reach the target RPM.

The most common issues that will cause an F111 Fan Motor Error to display on a GE Fridge are:

The fan motor is defective.
The fan blade is jammed.
The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F111 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F112 mean on a GE Fridge?

If your GE Fridge is displaying an F112 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F112 Fan Motor Error will set if the control board detects The deli pan fan feedback signal is missing when fan is running.

The most common issues that will cause an F112 Fan Motor Error to display on a GE Fridge are:

The fan motor is defective.
The fan blade is jammed.
The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F112 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F113 mean on a GE Fridge?

If your GE Fridge is displaying an F113 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F113 Fan Motor Error will set if the control board detects The deli pan fan feedback signal is present when the fan is off.

The most common issues that will cause an F113 Fan Motor Error to display on a GE Fridge are:

The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F113 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F114 mean on a GE Fridge?

If your GE Fridge is displaying an F114 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F114 Fan Motor Error will set if the control board detects The deli pan fan cannot reach the target RPM.

The most common issues that will cause an F114 Fan Motor Error to display on a GE Fridge are:

The fan motor is defective.
The fan blade is jammed.
The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F114 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F115 mean on a GE Fridge?

If your GE Fridge is displaying an F115 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F115 Fan Motor Error will set if the control board detects The odour filter fan feedback signal is missing when fan is running.

The most common issues that will cause an F115 Fan Motor Error to display on a GE Fridge are:

The fan motor is defective.
The fan blade is jammed.
The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F115 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F116 mean on a GE Fridge?

If your GE Fridge is displaying an F116 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F116 Fan Motor Error will set if the control board detects The odour filter fan feedback signal is present when the fan is off.

The most common issues that will cause an F116 Fan Motor Error to display on a GE Fridge are:

The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F116 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F117 mean on a GE Fridge?

If your GE Fridge is displaying an F117 fault code, it is indicating a Fan Motor Error has been detected by the internal self diagnostics system.

An F117 Fan Motor Error will set if the control board detects The odour filter fan cannot reach the target RPM.

The most common issues that will cause an F117 Fan Motor Error to display on a GE Fridge are:

The fan motor is defective.
The fan blade is jammed.
The main PCB is defective.
Wiring issue between the fan motor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F117 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F200 mean on a GE Fridge?

If your GE Fridge is displaying an F200 fault code, it is indicating a Defrost Error has been detected by the internal self diagnostics system.

An F200 Defrost Error will set if the control board detects The freezer section defrost heater on time has maxed out.

The most common issues that will cause an F200 Defrost Error to display on a GE Fridge are:

The defrost heater is defective.
The defrost temperature sensor is defective.
The defrost high limit sensor is defective.
The main PCB is defective.
Wiring issue between the defrost loop and the main PCB.
The defrost room is overwhelmed with ice.

Try turning the Fridge main power supply off for 1 minute. If the F200 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F201 mean on a GE Fridge?

If your GE Fridge is displaying an F201 fault code, it is indicating a Defrost Error has been detected by the internal self diagnostics system.

An F201 Defrost Error will set if the control board detects The refrigerator section defrost heater on time has maxed out.

The most common issues that will cause an F201 Defrost Error to display on a GE Fridge are:

The defrost heater is defective.
The defrost temperature sensor is defective.
The defrost high limit sensor is defective.
The main PCB is defective.
Wiring issue between the defrost loop and the main PCB.
The defrost room is overwhelmed with ice.

Try turning the Fridge main power supply off for 1 minute. If the F201 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F202 mean on a GE Fridge?

If your GE Fridge is displaying an F202 fault code, it is indicating a Defrost Error has been detected by the internal self diagnostics system.

An F202 Defrost Error will set if the control board detects The freezer section has experienced 5 or more abnormal defrost cycles.

The most common issues that will cause an F202 Defrost Error to display on a GE Fridge are:

The defrost heater is defective.
The defrost temperature sensor is defective.
The defrost high limit sensor is defective.
The main PCB is defective.
Wiring issue between the defrost loop and the main PCB.
The defrost room is overwhelmed with ice.

Try turning the Fridge main power supply off for 1 minute. If the F202 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F203 mean on a GE Fridge?

If your GE Fridge is displaying an F203 fault code, it is indicating a Defrost Error has been detected by the internal self diagnostics system.

An F203 Defrost Error will set if the control board detects The refrigerator section has experienced 5 or more abnormal defrost cycles.

The most common issues that will cause an F203 Defrost Error to display on a GE Fridge are:

The defrost heater is defective.
The defrost temperature sensor is defective.
The defrost high limit sensor is defective.
The main PCB is defective.
Wiring issue between the defrost loop and the main PCB.
The defrost room is overwhelmed with ice.

Try turning the Fridge main power supply off for 1 minute. If the F203 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F3 mean on a GE Fridge?

If your GE Fridge is displaying an F3 fault code, it is indicating a Thermistor Error has been detected by the internal self diagnostics system.

An F3 Thermistor Error will set if the control board detects The freezer cabinet thermistor (temperature sensor) signal is invalid.

The most common issues that will cause an F3 Thermistor Error to display on a GE Fridge are:

The thermistor (temperature sensor) is defective.
The main PCB is defective.
Wiring issue between the thermistor (temperature sensor) and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F3 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F301 mean on a GE Fridge?

If your GE Fridge is displaying an F301 fault code, it is indicating a Sealed System Error has been detected by the internal self diagnostics system.

An F301 Sealed System Error will set if the control board detects The compressor was off for 3 hours with the cooling system turned on.

The most common issues that will cause an F301 Sealed System Error to display on a GE Fridge are:

The compressor is defective.
The compressor start up circuit is defective.
Wiring issue.

Try turning the Fridge main power supply off for 1 minute. If the F301 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F303 mean on a GE Fridge?

If your GE Fridge is displaying an F303 fault code, it is indicating a Sealed System Error has been detected by the internal self diagnostics system.

An F303 Sealed System Error will set if the control board detects The refrigerator temperature exceeded 75°F.

The most common issues that will cause an F303 Sealed System Error to display on a GE Fridge are:

The refrigerator temperature is high.
The refrigerator temperature sensor is defective.
The main PCB is defective.
Wiring issue between the refrigerator temperature sensor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F303 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F304 mean on a GE Fridge?

If your GE Fridge is displaying an F304 fault code, it is indicating a Sealed System Error has been detected by the internal self diagnostics system.

An F304 Sealed System Error will set if the control board detects The freezer temperature exceeded 72.5°F.

The most common issues that will cause an F304 Sealed System Error to display on a GE Fridge are:

The freezer temperature is high.
The freezer temperature sensor is defective.
The main PCB is defective.
Wiring issue between the freezer temperature sensor and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F304 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F308 mean on a GE Fridge?

If your GE Fridge is displaying an F308 fault code, it is indicating a Sealed System Error has been detected by the internal self diagnostics system.

An F308 Sealed System Error will set if the control board detects The 3 way valve position cannot be detected by the main PCB.

The most common issues that will cause an F308 Sealed System Error to display on a GE Fridge are:

The 3 way valve is defective.
The main PCB is defective.
Wiring issue between the 3 way valve and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F308 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F4 mean on a GE Fridge?

If your GE Fridge is displaying an F4 fault code, it is indicating a Thermistor Error has been detected by the internal self diagnostics system.

An F4 Thermistor Error will set if the control board detects The freezer evaporator thermistor (temperature sensor) signal is invalid.

The most common issues that will cause an F4 Thermistor Error to display on a GE Fridge are:

The thermistor (temperature sensor) is defective.
The main PCB is defective.
Wiring issue between the thermistor (temperature sensor) and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F4 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F403 mean on a GE Fridge?

If your GE Fridge is displaying an F403 fault code, it is indicating a Main PCB internal Error has been detected by the internal self diagnostics system.

An F403 Main PCB internal Error will set if the control board detects The main PCB has an internal software error.

The most common issues that will cause an F403 Main PCB internal Error to display on a GE Fridge are:

Defective main PCB

Try turning the Fridge main power supply off for 1 minute. If the F403 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F404 mean on a GE Fridge?

If your GE Fridge is displaying an F404 fault code, it is indicating a Main PCB internal Error has been detected by the internal self diagnostics system.

An F404 Main PCB internal Error will set if the control board detects The main PCB has an internal software error.

The most common issues that will cause an F404 Main PCB internal Error to display on a GE Fridge are:

Defective main PCB

Try turning the Fridge main power supply off for 1 minute. If the F404 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F5 mean on a GE Fridge?

If your GE Fridge is displaying an F5 fault code, it is indicating a Thermistor Error has been detected by the internal self diagnostics system.

An F5 Thermistor Error will set if the control board detects The deli pan thermistor (temperature sensor) signal is invalid.

The most common issues that will cause an F5 Thermistor Error to display on a GE Fridge are:

The thermistor (temperature sensor) is defective.
The main PCB is defective.
Wiring issue between the thermistor (temperature sensor) and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F5 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F500 mean on a GE Fridge?

If your GE Fridge is displaying an F500 fault code, it is indicating a Dispenser Error has been detected by the internal self diagnostics system.

An F500 Dispenser Error will set if the control board detects The target hot water temperature cannot be reached.

The most common issues that will cause an F500 Dispenser Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F500 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F501 mean on a GE Fridge?

If your GE Fridge is displaying an F501 fault code, it is indicating a Dispenser Error has been detected by the internal self diagnostics system.

An F501 Dispenser Error will set if the control board detects The water flow meter signal is missing.

The most common issues that will cause an F501 Dispenser Error to display on a GE Fridge are:

The flow meter is defective.
The main PCB is defective.
Wiring issue between the flow meter and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F501 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F502 mean on a GE Fridge?

If your GE Fridge is displaying an F502 fault code, it is indicating a Dispenser Error has been detected by the internal self diagnostics system.

An F502 Dispenser Error will set if the control board detects The water flow meter signal is present with no water dispensing.

The most common issues that will cause an F502 Dispenser Error to display on a GE Fridge are:

The flow meter is defective.
The water valve is leaking.
The main PCB is defective.
Wiring issue between the flow meter and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F502 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F503 mean on a GE Fridge?

If your GE Fridge is displaying an F503 fault code, it is indicating a Dispenser Error has been detected by the internal self diagnostics system.

An F503 Dispenser Error will set if the control board detects The ice or water has stoped dispensing based on time (7 minute time out).

The most common issues that will cause an F503 Dispenser Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F503 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F504 mean on a GE Fridge?

If your GE Fridge is displaying an F504 fault code, it is indicating a Dispenser Error has been detected by the internal self diagnostics system.

An F504 Dispenser Error will set if the control board detects The hot water tank is unable to fill.

The most common issues that will cause an F504 Dispenser Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F504 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F507 mean on a GE Fridge?

If your GE Fridge is displaying an F507 fault code, it is indicating a Dispenser Error has been detected by the internal self diagnostics system.

An F507 Dispenser Error will set if the control board detects The cold water paddle switch input is open.

The most common issues that will cause an F507 Dispenser Error to display on a GE Fridge are:

The paddle switch is defective.
The PCB is defective.
Wiring issue between the paddle switch and the PCB.

Try turning the Fridge main power supply off for 1 minute. If the F507 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F508 mean on a GE Fridge?

If your GE Fridge is displaying an F508 fault code, it is indicating a Dispenser Error has been detected by the internal self diagnostics system.

An F508 Dispenser Error will set if the control board detects The cold water paddle switch input is shorted.

The most common issues that will cause an F508 Dispenser Error to display on a GE Fridge are:

The paddle switch is defective.
The PCB is defective.
Wiring issue between the paddle switch and the PCB.

Try turning the Fridge main power supply off for 1 minute. If the F508 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F509 mean on a GE Fridge?

If your GE Fridge is displaying an F509 fault code, it is indicating a Dispenser Error has been detected by the internal self diagnostics system.

An F509 Dispenser Error will set if the control board detects The hot water paddle switch input is open.

The most common issues that will cause an F509 Dispenser Error to display on a GE Fridge are:

The paddle switch is defective.
The PCB is defective.
Wiring issue between the paddle switch and the PCB.

Try turning the Fridge main power supply off for 1 minute. If the F509 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F510 mean on a GE Fridge?

If your GE Fridge is displaying an F510 fault code, it is indicating a Dispenser Error has been detected by the internal self diagnostics system.

An F510 Dispenser Error will set if the control board detects The hot water paddle switch input is shorted.

The most common issues that will cause an F510 Dispenser Error to display on a GE Fridge are:

The paddle switch is defective.
The PCB is defective.
Wiring issue between the paddle switch and the PCB.

Try turning the Fridge main power supply off for 1 minute. If the F510 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F511 mean on a GE Fridge?

If your GE Fridge is displaying an F511 fault code, it is indicating a Dispenser Error has been detected by the internal self diagnostics system.

An F511 Dispenser Error will set if the control board detects The door board ice maker mold thermistor (temperature sensor) is invalid.

The most common issues that will cause an F511 Dispenser Error to display on a GE Fridge are:

The thermistor (temperature sensor) is defective.
The main PCB is defective.
Wiring issue between the thermistor (temperature sensor) and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F511 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F512 mean on a GE Fridge?

If your GE Fridge is displaying an F512 fault code, it is indicating a Dispenser Error has been detected by the internal self diagnostics system.

An F512 Dispenser Error will set if the control board detects The door board ice box thermistor (temperature sensor) is invalid.

The most common issues that will cause an F512 Dispenser Error to display on a GE Fridge are:

The thermistor (temperature sensor) is defective.
The main PCB is defective.
Wiring issue between the thermistor (temperature sensor) and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F512 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F513 mean on a GE Fridge?

If your GE Fridge is displaying an F513 fault code, it is indicating a Dispenser Error has been detected by the internal self diagnostics system.

An F513 Dispenser Error will set if the control board detects The door board hot water 1 thermistor (temperature sensor) is invalid.

The most common issues that will cause an F513 Dispenser Error to display on a GE Fridge are:

The thermistor (temperature sensor) is defective.
The main PCB is defective.
Wiring issue between the thermistor (temperature sensor) and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F513 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F514 mean on a GE Fridge?

If your GE Fridge is displaying an F514 fault code, it is indicating a Dispenser Error has been detected by the internal self diagnostics system.

An F514 Dispenser Error will set if the control board detects The door board hot water 2 thermistor (temperature sensor) is invalid.

The most common issues that will cause an F514 Dispenser Error to display on a GE Fridge are:

The thermistor (temperature sensor) is defective.
The main PCB is defective.
Wiring issue between the thermistor (temperature sensor) and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F514 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F515 mean on a GE Fridge?

If your GE Fridge is displaying an F515 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F515 Hot Water or Ice maker Error will set if the control board detects The door board relay driver is shorted.

The most common issues that will cause an F515 Hot Water or Ice maker Error to display on a GE Fridge are:

The door board is defective.

Try turning the Fridge main power supply off for 1 minute. If the F515 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F516 mean on a GE Fridge?

If your GE Fridge is displaying an F516 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F516 Hot Water or Ice maker Error will set if the control board detects Hot Water Thermistor Fault.

The most common issues that will cause an F516 Hot Water or Ice maker Error to display on a GE Fridge are:

One of the thermistors (temperature sensors) is defective.
The main PCB is defective.
Wiring issue between one of the thermistors (temperature sensors) and the PCB.

Try turning the Fridge main power supply off for 1 minute. If the F516 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F517 mean on a GE Fridge?

If your GE Fridge is displaying an F517 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F517 Hot Water or Ice maker Error will set if the control board detects Hot Water AD Voltage Reference Voltage Fault.

The most common issues that will cause an F517 Hot Water or Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F517 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F518 mean on a GE Fridge?

If your GE Fridge is displaying an F518 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F518 Hot Water or Ice maker Error will set if the control board detects Water disabled due to low flow.

The most common issues that will cause an F518 Hot Water or Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F518 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F519 mean on a GE Fridge?

If your GE Fridge is displaying an F519 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F519 Hot Water or Ice maker Error will set if the control board detects The hot water is heating when tank is not full.

The most common issues that will cause an F519 Hot Water or Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F519 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F520 mean on a GE Fridge?

If your GE Fridge is displaying an F520 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F520 Hot Water or Ice maker Error will set if the control board detects Water disabled due to max fill timeout.

The most common issues that will cause an F520 Hot Water or Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F520 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F521 mean on a GE Fridge?

If your GE Fridge is displaying an F521 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F521 Hot Water or Ice maker Error will set if the control board detects Water disabled due to max purge timeout.

The most common issues that will cause an F521 Hot Water or Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F521 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F522 mean on a GE Fridge?

If your GE Fridge is displaying an F522 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F522 Hot Water or Ice maker Error will set if the control board detects Water disabled due to max purge timeout.

The most common issues that will cause an F522 Hot Water or Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F522 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F523 mean on a GE Fridge?

If your GE Fridge is displaying an F523 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F523 Hot Water or Ice maker Error will set if the control board detects Feature board communication error.

The most common issues that will cause an F523 Hot Water or Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F523 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F524 mean on a GE Fridge?

If your GE Fridge is displaying an F524 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F524 Hot Water or Ice maker Error will set if the control board detects Dispense nozzle movement error.

The most common issues that will cause an F524 Hot Water or Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F524 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F525 mean on a GE Fridge?

If your GE Fridge is displaying an F525 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F525 Hot Water or Ice maker Error will set if the control board detects Brew module not detected during brew.

The most common issues that will cause an F525 Hot Water or Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F525 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F526 mean on a GE Fridge?

If your GE Fridge is displaying an F526 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F526 Hot Water or Ice maker Error will set if the control board detects High flow during brewing.

The most common issues that will cause an F526 Hot Water or Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F526 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F527 mean on a GE Fridge?

If your GE Fridge is displaying an F527 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F527 Hot Water or Ice maker Error will set if the control board detects Low flow during brewing.

The most common issues that will cause an F527 Hot Water or Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F527 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F570 mean on a GE Fridge?

If your GE Fridge is displaying an F570 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F570 Hot Water or Ice maker Error will set if the control board detects Dispenser nozzle motor over current error.

The most common issues that will cause an F570 Hot Water or Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F570 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F571 mean on a GE Fridge?

If your GE Fridge is displaying an F571 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F571 Hot Water or Ice maker Error will set if the control board detects Air valves over current error.

The most common issues that will cause an F571 Hot Water or Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F571 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F572 mean on a GE Fridge?

If your GE Fridge is displaying an F572 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F572 Hot Water or Ice maker Error will set if the control board detects Air pump over current error.

The most common issues that will cause an F572 Hot Water or Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F572 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F573 mean on a GE Fridge?

If your GE Fridge is displaying an F573 fault code, it is indicating a Hot Water or Ice maker Error has been detected by the internal self diagnostics system.

An F573 Hot Water or Ice maker Error will set if the control board detects Feature Board hardware fault.

The most common issues that will cause an F573 Hot Water or Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F573 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F6 mean on a GE Fridge?

If your GE Fridge is displaying an F6 fault code, it is indicating a Thermistor Error has been detected by the internal self diagnostics system.

An F6 Thermistor Error will set if the control board detects The refrigerator evaporator thermistor (temperature sensor) signal is invalid.

The most common issues that will cause an F6 Thermistor Error to display on a GE Fridge are:

The thermistor (temperature sensor) is defective.
The main PCB is defective.
Wiring issue between the thermistor (temperature sensor) and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F6 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F601 mean on a GE Fridge?

If your GE Fridge is displaying an F601 fault code, it is indicating a Ice maker Error has been detected by the internal self diagnostics system.

An F601 Ice maker Error will set if the control board detects The ice maker in the fridge section is stuck in Harvest Fix Mode.

The most common issues that will cause an F601 Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F601 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F602 mean on a GE Fridge?

If your GE Fridge is displaying an F602 fault code, it is indicating a Ice maker Error has been detected by the internal self diagnostics system.

An F602 Ice maker Error will set if the control board detects The ice maker in the fridge section enters Harvest Fix Mode 3 out of 10 harvests.

The most common issues that will cause an F602 Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F602 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F603 mean on a GE Fridge?

If your GE Fridge is displaying an F603 fault code, it is indicating a Ice maker Error has been detected by the internal self diagnostics system.

An F603 Ice maker Error will set if the control board detects The ice maker in the fridge section enters fault mode.

The most common issues that will cause an F603 Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F603 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F604 mean on a GE Fridge?

If your GE Fridge is displaying an F604 fault code, it is indicating a Ice maker Error has been detected by the internal self diagnostics system.

An F604 Ice maker Error will set if the control board detects The ice maker in the fridge section has no water supply detected.

The most common issues that will cause an F604 Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F604 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F605 mean on a GE Fridge?

If your GE Fridge is displaying an F605 fault code, it is indicating a Ice maker Error has been detected by the internal self diagnostics system.

An F605 Ice maker Error will set if the control board detects The ice maker in the fridge section continues to sense bucket full after ice dispense.

The most common issues that will cause an F605 Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F605 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F606 mean on a GE Fridge?

If your GE Fridge is displaying an F606 fault code, it is indicating a Ice maker Error has been detected by the internal self diagnostics system.

An F606 Ice maker Error will set if the control board detects The ice maker in the fridge section mold heater is not heating.

The most common issues that will cause an F606 Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F606 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F651 mean on a GE Fridge?

If your GE Fridge is displaying an F651 fault code, it is indicating a Ice maker Error has been detected by the internal self diagnostics system.

An F651 Ice maker Error will set if the control board detects The ice maker in the freezer is stuck in Harvest Fix Mode.

The most common issues that will cause an F651 Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F651 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F652 mean on a GE Fridge?

If your GE Fridge is displaying an F652 fault code, it is indicating a Ice maker Error has been detected by the internal self diagnostics system.

An F652 Ice maker Error will set if the control board detects The ice maker in the freezer enters Harvest Fix Mode 3 out of 10 harvests.

The most common issues that will cause an F652 Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F652 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F653 mean on a GE Fridge?

If your GE Fridge is displaying an F653 fault code, it is indicating a Ice maker Error has been detected by the internal self diagnostics system.

An F653 Ice maker Error will set if the control board detects The ice maker in the freezer enters Fault Mode.

The most common issues that will cause an F653 Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F653 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F654 mean on a GE Fridge?

If your GE Fridge is displaying an F654 fault code, it is indicating a Ice maker Error has been detected by the internal self diagnostics system.

An F654 Ice maker Error will set if the control board detects The ice maker in the freezer has no water supply detected.

The most common issues that will cause an F654 Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F654 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F655 mean on a GE Fridge?

If your GE Fridge is displaying an F655 fault code, it is indicating a Ice maker Error has been detected by the internal self diagnostics system.

An F655 Ice maker Error will set if the control board detects The ice maker in the freezer mold heater is not heating.

The most common issues that will cause an F655 Ice maker Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F655 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F700 mean on a GE Fridge?

If your GE Fridge is displaying an F700 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F700 Interaction Error will set if the control board detects Stuck keys are detected on the Dispenser Board.

The most common issues that will cause an F700 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F700 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F701 mean on a GE Fridge?

If your GE Fridge is displaying an F701 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F701 Interaction Error will set if the control board detects Stuck keys are detected on the Internal Temp Board.

The most common issues that will cause an F701 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F701 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F702 mean on a GE Fridge?

If your GE Fridge is displaying an F702 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F702 Interaction Error will set if the control board detects Stuck keys are detected on the Deli Pan.

The most common issues that will cause an F702 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F702 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F703 mean on a GE Fridge?

If your GE Fridge is displaying an F703 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F703 Interaction Error will set if the control board detects Key inputs are detected on the Temp Board when the door is closed.

The most common issues that will cause an F703 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F703 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F704 mean on a GE Fridge?

If your GE Fridge is displaying an F704 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F704 Interaction Error will set if the control board detects Key inputs are detected on the Deli Pan Board when the door is closed.

The most common issues that will cause an F704 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F704 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F705 mean on a GE Fridge?

If your GE Fridge is displaying an F705 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F705 Interaction Error will set if the control board detects AutoFill communication error.

The most common issues that will cause an F705 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F705 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F706 mean on a GE Fridge?

If your GE Fridge is displaying an F706 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F706 Interaction Error will set if the control board detects AutoFill version error.

The most common issues that will cause an F706 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F706 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F707 mean on a GE Fridge?

If your GE Fridge is displaying an F707 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F707 Interaction Error will set if the control board detects ACM/Comm communication error.

The most common issues that will cause an F707 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F707 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F708 mean on a GE Fridge?

If your GE Fridge is displaying an F708 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F708 Interaction Error will set if the control board detects COM wrong version.

The most common issues that will cause an F708 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F708 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F709 mean on a GE Fridge?

If your GE Fridge is displaying an F709 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F709 Interaction Error will set if the control board detects Cold Water Cup Switch input missing and 0x70 message is received from COM (ACM Only).

The most common issues that will cause an F709 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F709 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F710 mean on a GE Fridge?

If your GE Fridge is displaying an F710 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F710 Interaction Error will set if the control board detects Cold Water Cup Switch input present and no dispense message is received from COM (ACM Only).

The most common issues that will cause an F710 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F710 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F711 mean on a GE Fridge?

If your GE Fridge is displaying an F711 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F711 Interaction Error will set if the control board detects Hot Water Cup Switch input missing and dispense message is received that requires the cup switch (ACM Only).

The most common issues that will cause an F711 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F711 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F712 mean on a GE Fridge?

If your GE Fridge is displaying an F712 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F712 Interaction Error will set if the control board detects Hot Water Cup Switch input present and no dispense message is received (ACM Only).

The most common issues that will cause an F712 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F712 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F713 mean on a GE Fridge?

If your GE Fridge is displaying an F713 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F713 Interaction Error will set if the control board detects The fridge door is open for 15 minutes.

The most common issues that will cause an F713 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F713 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F714 mean on a GE Fridge?

If your GE Fridge is displaying an F714 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F714 Interaction Error will set if the control board detects The fridge door is open for 60 minutes in the last 24 hours.

The most common issues that will cause an F714 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F714 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F715 mean on a GE Fridge?

If your GE Fridge is displaying an F715 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F715 Interaction Error will set if the control board detects The fridge door is opened 50 times in the last 24 hours.

The most common issues that will cause an F715 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F715 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F716 mean on a GE Fridge?

If your GE Fridge is displaying an F716 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F716 Interaction Error will set if the control board detects The freezer door is open for 15 minutes.

The most common issues that will cause an F716 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F716 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F717 mean on a GE Fridge?

If your GE Fridge is displaying an F717 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F717 Interaction Error will set if the control board detects The freezer door is open for 60 minutes in the last 24 hours.

The most common issues that will cause an F717 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F717 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F718 mean on a GE Fridge?

If your GE Fridge is displaying an F718 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F718 Interaction Error will set if the control board detects The freezer door is opened 50 times in the last 24 hours.

The most common issues that will cause an F718 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F718 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F722 mean on a GE Fridge?

If your GE Fridge is displaying an F722 fault code, it is indicating a Interaction Error has been detected by the internal self diagnostics system.

An F722 Interaction Error will set if the control board detects Display board error.

The most common issues that will cause an F722 Interaction Error to display on a GE Fridge are:

N/A See service manual.

Try turning the Fridge main power supply off for 1 minute. If the F722 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F8 mean on a GE Fridge?

If your GE Fridge is displaying an F8 fault code, it is indicating a Thermistor Error has been detected by the internal self diagnostics system.

An F8 Thermistor Error will set if the control board detects The ambient air thermistor (temperature sensor) signal is invalid.

The most common issues that will cause an F8 Thermistor Error to display on a GE Fridge are:

The thermistor (temperature sensor) is defective.
The main PCB is defective.
Wiring issue between the thermistor (temperature sensor) and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F8 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does F9 mean on a GE Fridge?

If your GE Fridge is displaying an F9 fault code, it is indicating a Thermistor Error has been detected by the internal self diagnostics system.

An F9 Thermistor Error will set if the control board detects The ambient air humidity sensor signal is invalid.

The most common issues that will cause an F9 Thermistor Error to display on a GE Fridge are:

The thermistor (temperature sensor) is defective.
The main PCB is defective.
Wiring issue between the thermistor (temperature sensor) and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the F9 code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does FF mean on a GE Fridge?

If your GE Fridge is displaying an FF fault code, it is indicating a High Temp Error has been detected by the internal self diagnostics system.

An FF High Temp Error will set if the control board detects Check frozen food for thawing because the temperature is rising too high.

The most common issues that will cause an FF High Temp Error to display on a GE Fridge are:

The fridge or freezer door is not closing properly.
Cooling system fault.
Faulty door gasket.

Try turning the Fridge main power supply off for 1 minute. If the FF code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does HRS mean on a GE Fridge?

If your GE Fridge is displaying an HRS fault code, it is indicating a Defrost Error has been detected by the internal self diagnostics system.

An HRS Defrost Error will set if the control board detects Fridge or freezer is stuck in defrost mode.

The most common issues that will cause an HRS Defrost Error to display on a GE Fridge are:

The main PCB is defective.
Wiring issue between the defrost loop and the main PCB.

Try turning the Fridge main power supply off for 1 minute. If the HRS code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does PF mean on a GE Fridge?

If your GE Fridge is displaying an PF fault code, it is indicating a Power Failure Error has been detected by the internal self diagnostics system.

An PF Power Failure Error will set if the control board detects The power to the refrigerator has been interrupted.

The most common issues that will cause an PF Power Failure Error to display on a GE Fridge are:

The power to the refrigerator has been interrupted.

Try turning the Fridge main power supply off for 1 minute. If the PF code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does tC mean on a GE Fridge?

If your GE Fridge is displaying an tC fault code, it is indicating a Turbo Cool has been detected by the internal self diagnostics system.

An tC Turbo Cool will set if the control board detects This is not an error.

The most common issues that will cause an tC Turbo Cool to display on a GE Fridge are:

The Turbo Cool Function is turned on

Try turning the Fridge main power supply off for 1 minute. If the tC code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

What does tF mean on a GE Fridge?

If your GE Fridge is displaying an tF fault code, it is indicating a Turbo Freeze has been detected by the internal self diagnostics system.

An tF Turbo Freeze will set if the control board detects This is not an error.

The most common issues that will cause an tF Turbo Freeze to display on a GE Fridge are:

The Turbo Freeze Function is turned on

Try turning the Fridge main power supply off for 1 minute. If the tF code returns after turning the power supply back on, the problem causing the fault will need to be repaired to clear the error

GE Fridge Error Codes Disclaimer

The GE Fridge Error Codes information contained on this page is provided for informational purposes only. ApplianceFaultCodes.com does not guarantee the information to be correct or give a proper diagnosis of any appliance. Always take proper safety precautions when installing or repairing any major appliance.